Каталог Winstar монолитный инструмент 2020 - страница 242

Solid Carbide Endmills Recommended Cutting Conditions ら峿⎖⏙╒㜇 Table 040 G550 Seires EPBSC2 H600 Seires EHBSC2 Material CARBON STEEL / ALLOY STEEL ALLOY STEEL / TOOL STEEL PREHARDENED STEEL ⽴₅㣟㜨 䩂亯撋 0 ▗捠撋 ▗捠撋 0 ⽴⌆撋SCM, SKT, SKD 屎幹撋NAK80 CENA1 Hardness 䧻〵 HB180~250 HRC25~35 HRC35~45 VC 佩憮〵 120 (m/min) 95 (m/min) 79 (m/min) Dia ) ⎒ㄠ * RPM 惘憮 Feed (mm/min)懁仵 ap(mm) ae RPM Feed (mm/min) ap(mm)惘憮懁仵(mm)ae RPM Feed (mm/min) ap(mm)惘憮懁仵(mm)ae(mm) 1R 37470 936 0.14 0.2 29660 740 0.14 0.2 24660 616 0.14 0.2 2R 18730 1120 0.28 0.4 14830 890 0.28 0.4 12330 740 0.28 0.4 3R 12490 936 0.42 0.6 9890 740 0.42 0.6 8220 616 0.42 0.6 4R 9366 750 0.56 0.8 7415 593 0.56 0.8 6170 494 0.56 0.8 5R 7490 636 0.7 1 5930 504 0.7 1 4930 420 0.7 1 6R 6244 560 0.84 1.2 4940 444 0.84 1.2 4110 370 0.84 1.2 Material HARDENED STEEL STAINLESS STEEL CAST IRON ⽴₅㣟㜨 㽻䇺撋SKD61, SKD11 ᾜ斌撋SUS304 316 旓旄FC / FCD Hardness 䧻〵 HRC 40~55) VC 佩憮〵 48 (m/min) 79 (m/min) 120 (m/min) Dia ) ⎒ㄠ * RPM 惘憮 Feed (mm/min)懁仵 ap(mm) ae RPM Feed (mm/min) ap(mm)惘憮懁仵(mm)ae RPM Feed (mm/min) ap(mm)惘憮懁仵(mm)ae(mm) 1R 14990 374 0.14 0.2 24660 616 0.14 0.2 37470 936 0.14 0.2 2R 7490 450 0.28 0.4 12330 740 0.28 0.4 18730 1120 0.28 0.4 3R 4995 374 0.42 0.6 8220 616 0.42 0.6 12490 936 0.42 0.6 4R 3750 300 0.56 0.8 6170 494 0.56 0.8 9366 750 0.56 0.8 5R 3000 255 0.7 1 4930 420 0.7 1 7490 636 0.7 1 6R 2500 225 0.84 1.2 4110 370 0.84 1.2 6244 560 0.84 1.2 ʰ H600 Series, vc, rpm and feed increase 20% 1.Use as highly rigid and accurate machine as possible. 2.If the rpm available is lower than the recommend condition, please reduce the feed rate to the same ratio. 3.Use long shank type please reduce the rpm and feed rate. 4.The Feed and RPM may be changed depending on the M/C conditions ,lubricating and cooling system. 2/ 䡰╾劌䚷汧⏪ㆶҷ汧乍㯮〙Ҹ 3/ 㯮〙惘憮ᾜ彂㟑虇屚ⶖ懁仵ҷ惘憮▛㵣ℚᾚ屎Ҹ 4/ 朆㥓⤚㎥⇞㚉懝⪶㟑屚嬥㉔㹐ᾚ屎惘憮ҷ懁仵Ҹ 5/ ⁴ᾙ㜇㙩䉉ら峿⇋虇懸䜅䠓㨬₅⁜榗嬥㯮╿䑏㹐ҷ⫍㹊⌆♐幹ҷ䃳䁠⍆┊亊伀ʫ䳘㛈崙Ҹ SA232