Каталог Winstar монолитный инструмент 2020 - страница 229

Solid Carbide Endmills Solid Carbide Endmills Recommended Cutting Conditions ら峿⎖⏙╒㜇 Table 027 G550 Seires EPSSC2 G450 Seires EPSSA2 Material CARBON STEEL / ALLOY STEEL ALLOY STEEL / TOOL STEEL PREHARDENED STEEL ⽴₅㣟㜨 䩂亯撋 0 ▗捠撋 ▗捠撋 0 ⽴⌆撋SCM, SKT, SKD 屎幹撋NAK80 CENA1 Hardness 䧻〵 HB180~250 HRC25~35 HRC35~45 VC 佩憮〵 120(m/min) 95(m/min) 79(m/min) Dia ) ⎒ㄠ * RPM 惘憮 Feed (mm/min)懁仵 ap (mm) ae RPM Feed (mm/min) ap(mm)惘憮懁仵(mm)ae RPM Feed (mm/min) ap(mm)惘憮懁仵(mm)ae(mm) 3mm 12700 380 1.5 3 10000 300 0.9 3 8386 251 0.15 3 4mm 9550 382 2 4 7560 302 1.2 4 6290 251 0.2 4 6mm 6370 445 3 6 5040 352 1.8 6 4200 294 0.3 6 8mm 4770 333 4 8 3780 264 2.4 8 3140 220 0.4 8 10mm 3820 230 5 10 3020 181 3 10 2515 150 0.5 10 12mm 3180 190 6 12 2520 151 3.6 12 2100 126 0.6 12 Material HARDENED STEEL STAINLESS STEEL CAST IRON ⽴₅㣟㜨 㽻䇺撋SKD61, SKD11 ᾜ斌撋SUS304 316 旓旄FC / FCD Hardness 䧻〵 HRC 40~55) VC 佩憮〵 48(m/min) 79(m/min) 120(m/min) Dia ) ⎒ㄠ * RPM 惘憮 Feed (mm/min)懁仵 ap (mm) ae RPM Feed (mm/min) ap(mm)惘憮懁仵(mm)ae RPM Feed (mm/min) ap(mm)惘憮懁仵(mm)ae(mm) 3mm 5095 152 0.15 3 8386 251 0.15 3 12700 380 1.5 3 4mm 3820 152 0.2 4 6290 251 0.2 4 9550 382 2 4 6mm 2548 178 0.3 6 4200 294 0.3 6 6370 445 3 6 8mm 1910 133 0.4 8 3140 220 0.4 8 4770 333 4 8 10mm 1528 92 0.5 10 2515 150 0.5 10 3820 230 5 10 12mm 1274 76 0.6 12 2100 126 0.6 12 3180 190 6 12 1.Use as highly rigid and accurate machine as possible. 2.If the rpm available is lower than the recommend condition, please reduce the feed rate to the same ratio. 3.Use long shank type please reduce the rpm and feed rate. 4.The Feed and RPM may be changed depending on the M/C conditions ,lubricating and cooling system. 2/ 䡰╾劌䚷汧⏪ㆶҷ汧乍㯮〙Ҹ 3/ 㯮〙惘憮ᾜ彂㟑虇屚ⶖ懁仵ҷ惘憮▛㵣ℚᾚ屎Ҹ 4/ 朆㥓⤚㎥⇞㚉懝⪶㟑屚嬥㉔㹐ᾚ屎惘憮ҷ懁仵Ҹ 5/ ⁴ᾙ㜇㙩䉉ら峿⇋虇懸䜅䠓㨬₅⁜榗嬥㯮╿䑏㹐ҷ⫍㹊⌆♐幹ҷ䃳䁠⍆┊亊伀ʫ䳘㛈崙Ҹ SA219