Каталог Widia трохоидальное фрезерование - страница 24

Предыдущая страница Следующая страница

Навигация

Application Data • Series 4717 4727 • VariMill I™

  • Series 4717 • VariMill I

Side Milling (A) Finish Rough Recommended feed per tooth TIALN TIALN (fz=mm/th) for side milling (A).

A Cutting Speed A Cutting Speed

— vc — vc D1 — Diameter

m/min m/min Material

Groupapaeminmaxapaeminmaxmm6,08,010,012,016,020,0
1Ap1 max0,05 x D*300–400Ap1 max0,2 x D150–200fz0,0440,0600,0720,0830,0920,114
2Ap1 max0,05 x D*280–380Ap1 max0,2 x D140–190fz0,0440,0600,0720,0830,0920,114
3Ap1 max0,05 x D*240–320Ap1 max0,2 x D120–160fz0,0360,0500,0610,0700,0790,101

P

4Ap1 max0,05 x D*180–300Ap1 max0,2 x D90–150fz0,0330,0450,0540,0620,0700,088
5Ap1 max0,05 x D*120–200Ap1 max0,2 x D60–100fz0,0290,0400,0480,0560,0630,081
6Ap1 max0,05 x D*100–150Ap1 max0,2 x D50–75fz0,0250,0340,0400,0470,0520,065
1Ap1 max0,05 x D*180–230Ap1 max0,2 x D90–115fz0,0360,0500,0610,0700,0790,101
M 2Ap1 max0,05 x D*120–160Ap1 max0,2 x D60–80fz0,0290,0400,0480,0560,0630,081
3Ap1 max0,05 x D*120–140Ap1 max0,2 x D60–70fz0,0250,0340,0400,0470,0520,065
1Ap1 max0,05 x D*240–300Ap1 max0,2 x D120–150fz0,0440,0600,0720,0830,0920,114
K 2Ap1 max0,05 x D*220–260Ap1 max0,2 x D110–130fz0,0360,0500,0610,0700,0790,101
3Ap1 max0,05 x D*200–260Ap1 max0,2 x D100–130fz0,0290,0400,0480,0560,0630,081
1Ap1 max0,05 x D*100–180Ap1 max0,2 x D50–90fz0,0360,0500,0610,0700,0790,101
2Ap1 max0,05 x D*50–80Ap1 max0,2 x D25–40fz0,0360,0500,0610,0700,0790,101

S

3Ap1 max0,05 x D*120–160Ap1 max0,2 x D60–80fz0,0190,0260,0320,0370,0420,054
4Ap1 max0,05 x D*100–120Ap1 max0,2 x D50–60fz0,0260,0370,0450,0520,0580,074
H1Ap1 max0,05 x D*160–280Ap1 max0,2 x D80–140fz0,0330,0450,0540,0620,0700,088
  • Series 4727 • VariMill I

Side Milling (A)

Finish Rough Recommended feed per tooth

TIALN TIALN (fz=mm/th) for side milling (A).

A Cutting Speed — vc A Cutting Speed — vc

D1 — Diameter m/min m/min Material

Groupapaeminmaxapaeminmaxmm12,016,020,0
1Ap1 max0,05 x D*300–400Ap1 max0,2 x D150–200fz0,0830,1010,114
2Ap1 max0,05 x D*280–380Ap1 max0,2 x D140–190fz0,0830,1010,114
3Ap1 max0,05 x D*240–320Ap1 max0,2 x D120–160fz0,0700,0870,101

P

4Ap1 max0,05 x D*180–300Ap1 max0,2 x D90–150fz0,0620,0770,088
5Ap1 max0,05 x D*120–200Ap1 max0,2 x D60–100fz0,0560,0700,081
6Ap1 max0,05 x D*100–150Ap1 max0,2 x D50–75fz0,0470,0570,065
1Ap1 max0,05 x D*180–230Ap1 max0,2 x D90–115fz0,0700,0870,101
M 2Ap1 max0,05 x D*120–160Ap1 max0,2 x D60–80fz0,0560,0700,081
3Ap1 max0,05 x D*120–140Ap1 max0,2 x D60–70fz0,0470,0570,065
1Ap1 max0,05 x D*240–300Ap1 max0,2 x D120–150fz0,0830,1010,114
K 2Ap1 max0,05 x D*220–260Ap1 max0,2 x D110–130fz0,0700,0870,101
3Ap1 max0,05 x D*200–260Ap1 max0,2 x D100–130fz0,0560,0700,081
1Ap1 max0,05 x D*100–180Ap1 max0,2 x D50–90fz0,0700,0870,101
2Ap1 max0,05 x D*50–80Ap1 max0,2 x D25–40fz0,0700,0870,101

S

3Ap1 max0,05 x D*120–160Ap1 max0,2 x D60–80fz0,0370,0460,054
4Ap1 max0,05 x D*100–120Ap1 max0,2 x D50–60fz0,0520,0640,074
H1Ap1 max0,05 x D*160–280Ap1 max0,2 x D80–140fz0,0620,0770,088

*For cutting data above, use ae )0,8mm. NOTE: Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group. Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group. Above parameters are based on ideal conditions. For smaller taper machining centres, please adjust parameters accordingly on >12mm diameters.