Каталог Widia all star 2020 - страница 387

• TABLE OF CONTENTS
• INDEXABLE MILLING
• 0º/90º SHOULDER MILLS
• 90° HIGH-SPEED CUTTING MILLS
• FACE MILLS
• HIGH-FEED MILLS
• COPY MILLS
• SOLID END MILLING
• HIGH-PERFORMANCE SOLID CARBIDE END MILLS
• GENERAL PURPOSE SOLID CARBIDE END MILLS
• HOLEMAKING
• SOLID CARBIDE DRILLS
• MODULAR DRILLS
• INDEXABLE DRILLS
• TAPPING
• TURNING
• HIGH-PERFORMANCE INSERTS
• GROOVING & CUT-OFF
• Informational Icons Guide
• Material Overview • DIN

feed rate [in/rev (mm/rev)] feed rate [in/rev (mm/rev)]feed rate [in/rev (mm/rev)] TURNINGTAPPINGHOLEMAKINGSOLID END MILLINGINDEXABLE MILLING Grooving and Cut-Off • WMT™ Feed Values for Grooving Inserts CM Cut-Off Medium • Double-ended, V-bottom and top, mechanically .012 (0,30) clamped.• Neutral, right-, and left-hand lead angles up to 12˚. .011 (0,28) • Designed to increase speed and feed. .010 (0,25) • Chip geometry designed for excellent chip control and minimised cutting pressure on various materials. .0009 (0,23) • Ideal for 300 Series stainless steel, tool steel, titanium, INCONEL®, and other nickel-based alloys .0008 (0,20) at moderate speeds and feeds. .0007 (0,18) .0006 (0,15) .0005 (0,13) CM-W Cut-Off • Wiper flats where surface finish is critical. Medium with Wiper • Double-ended, V-bottom, and top,mechanically clamped. .0004 (0,10) • Neutral, right-, and left-hand lead angles up to 12˚. .0003 (0,08) • Designed to increase speed and feed. • Chip geometry designed for excellent chip control .0002 (0,05) and minimised cutting pressure on various materials. width of cut .062 .094 .125 .157 [in (mm)] (1,5 and 2,0) (2,5) (3,0) (4,0) 1 Recommended Starting Feed .250 (6,3) PT Plunge, Groove, • High positive rake geometry for low .200 size 8 and Turn Inserts cutting force, especially in soft materials.• Deep grooving tool for plunge and turn (5,5) size 7 O.D. and face grooving operations. .150 size 6 • Delivers chip control over full rangeof DOC when turning. (4,0) size 5 • Cuts in both axial and radial directions. .100 size 4 (2,5) .060 size 3 (1,6) .040 size 2 (1,0) R0,2 R1,06 PC Grooving and • Superior chip control. .020 Profiling Inserts • Full nose radius geometry for plungeand contour operations.• Effective cutting edge geometry exceeds(0,5)turn/profile feed.004 .006 .010 .016mm/rev (in/rev)(0,1)(0,16)(0,25)(0,4) 180° for increased versatility. plunge groove feed .002 .004 .006 .012 mm/rev (in/rev) (0,05) (0,1) (0,16) (0,30) .250 (6,3) .200 (5,5) .150 size 8 PH Plunge, Groove, • Excellent performance in greater than 35 HRC. (4,0) size 6 and Turn Inserts • Deep grooving tool for plunge and turn O.D.and face grooving operations. .100 size 5 • Delivers chip control over full range of DOC (2,5) when turning. size 4 • Delivers superior chip control in interrupted cuts. .060 (1,6) size 3 .040 size 2 (1,0) .020 (0,5) turn/profile feed .004 .006 .010 .016 mm/rev (in/rev) (0,1) (0,16) (0,25) (0,4) plunge groove feed .002 .004 .006 .012 mm/rev (in/rev) (0,05) (0,1) (0,16) (0,30) widia.com E99