Общий каталог Sumitomo 2019 - 2020 - страница 966

DrillingSolidIndexableIndexableHead TypeInsert TypeReamersBrazedOthers DC h7 Stock DCON h6 DC h7 DCSFMS DCON h6 SEC-MultiDrills SMD Type (Internal Coolant Supply) MFS Carbon Steel/Alloy Steelup to 0.28%Carbon Steel/Alloy Steelfrom 0.29%HardenedSteelup to 45HRCStainlessSteelCast IronDuctileCast IronAluminumAlloy Indexable head Coolant Hole Indexable The dimensions listed on this page are with MFS Type head installed. Coat Type The 12D shank has no side lock flat. *Refer to N38 for the tolerance of h6 and h7 Steel Mounted Figure Fig 1 Fig 2 3D/5D/8D LU LSOAL LU LS1.5D/12DOAL J Holder ø12.0 to 22.8mm Dimensions with MFS Type set Parts Dimensions (mm)Cap ScrewWrench Dia.DC HoleDepth Cat. No. Effective Length Overall Length Shank FlangeDia. ShankDia. Fig(L/D)LUOALLSDCSFMSDCON Nm 1.5 SMDH 120S ● 26 89 20 2 0.75 12.0 ≤ D < 12.5 3 SMDH 120M ● 44 105 485SMDH 120L●69130 Q 16 1 BXD02208IP to TRDR08IP11.00 1.5 SMDH 125S ● 26 89 20 2 0.75 12.5 ≤ D < 13.0 3 SMDH 125M ● 44 105 485SMDH 125L●69130 Q 16 1 BXD02208IP to TRDR08IP11.00 1.5 SMDH 130S ● 27 90 20 2 0.75 13.0 ≤ D < 13.5 3 SMDH 130M ● 47 110 485SMDH 130L●74140 Q 16 1 BXD02208IP to TRDR08IP11.00 1.5 SMDH 140S ● 31 94 20 2 3 SMDH 140M ● 53 117 1 0.75 13.5 ≤ D ≤ 14.5 5 SMDH 140L ● 82 147 48 Q 16 1 BXD02208IP to TRDR08IP 8 SMDH 140D ● 125 192 1 1.00 12 SMDH 140-12D ● 168 236 20 2 1.5 SMDH 150S ● 32 97 25 2 3 SMDH 150M ● 56 127 1 0.75 14.5 < D ≤ 15.5 5 SMDH 150L ● 87 157 50 Q 20 1 BXD02208IP to TRDR08IP 8 SMDH 150D ● 134 202 1 1.00 12 SMDH 150-12D ● 180 250 25 2 1.5 SMDH 160S ● 35 100 25 2 3 SMDH 160M ● 60 132 1 0.93 15.5 < D ≤ 16.5 5 SMDH 160L ● 93 167 50 Q 20 1 BXD02509IP to TRDR10IP 8 SMDH 160D ● 142 212 1 1.24 12 SMDH 160-12D ● 192 263 25 2 1.5 SMDH 170S ● 37 102 25 2 3 SMDH 170M ● 63 137 1 0.93 16.5 < D ≤ 17.5 5 SMDH 170L ● 98 172 50 Q 20 1 BXD02509IP to TRDR10IP 8 SMDH 170D ● 151 222 1 1.24 12 SMDH 170-12D ● 204 275 25 2 1.5 SMDH 180S ● 39 104 25 2 3 SMDH 180M ● 67 142 1 0.93 17.5 < D ≤ 18.5 5 SMDH 180L ● 104 177 50 Q 20 1 BXD02509IP to TRDR10IP 8 SMDH 180D ● 159 227 1 1.24 12 SMDH 180-12D ● 216 287 25 2 1.5 SMDH 190S ● 41 112 30 2 3 SMDH 190M ● 70 157 1 1.83 18.5 < D ≤ 19.5 5 SMDH 190L ● 109 192 56 Q 25 1 BXD03011IP to TRDR15IP 8 SMDH 190D ● 168 252 1 2.44 12 SMDH 190-12D ● 228 306 30 2 1.5 SMDH 200S ● 43 114 30 2 3 SMDH 200M ● 74 157 1 1.83 19.5 < D ≤ 20.5 5 SMDH 200L ● 115 197 56 Q 25 1 BXD03011IP to TRDR15IP 8 SMDH 200D ● 176 267 1 2.44 12 SMDH 200-12D ● 240 318 30 2 1.5 SMDH 210S ● 45 116 30 2 3 SMDH 210M ● 77 157 1 1.83 20.5 < D ≤ 21.5 5 SMDH 210L ● 120 197 56 Q 25 1 BXD03011IP to TRDR15IP 8 SMDH 210D ● 185 262 1 2.44 12 SMDH 210-12D ● 252 330 30 2 1.5 SMDH 220S ● 46 117 30 2 3 SMDH 220M ● 80 161 1 2.79 21.5 < D ≤ 22.8 5 SMDH 220L ● 125 201 56 Q 25 1 BXD03512IP to TRDR15IP 8 SMDH 220D ● 192 271 1 3.72 12 SMDH 220-12D ● 264 343 30 2 LU for 12D holder is the value with typical diameter. Recommended Cutting Conditions J104 MFS Type Head J105 J106 N m Recommended Tightening Torque (N·m)