Общий каталог Sumitomo 2019 - 2020 - страница 960

DrillingSolidIndexableIndexableHead TypeInsert TypeReamersBrazedOthers 140° DC h7 Stock DCON h6 140° DC h7 DCSFMS DCON h6 SEC-MultiDrills MTL Carbon Steel/Alloy Steelup to 0.28%Carbon Steel/Alloy Steelfrom 0.29%TemperedSteelHardenedSteelup to 45HRCStainlessSteelCast IronDuctileCast Iron SMD Type (Internal Coolant Supply) MEL Carbon Steel/Alloy Steelup to 0.28%Carbon Steel/Alloy Steelfrom 0.29%HardenedSteelup to 45HRCStainlessSteelTi AlloyHeat-resistantSteelCast IronDuctileCast IronAluminumAlloy Indexable head Indexable head Coolant Hole Indexable The 12D shank has no side lock flat. Coat Type Type *Refer to N38 for the tolerance of h6 and h7 Steel Mounted Figure Fig 1 Fig 2 LU LS LU LS 3D/5D/8D OAL 1.5D/12D OAL J Holder ø12.0 to 21.5mm Dimensions with MTL Type/MEL Type set Parts Dimensions (mm)Cap ScrewWrench Dia.DC HoleDepth Cat. No.(L/D) EffectiveLengthOverallLengthShankFlangeDia.LUOALLSDCSFMSShankDia.DCONIndexableHead Fig Nm 1.5 SMDH 120S ● 28 91 20 2 0.75 12.0 ≤ D < 12.5 3 SMDH 120M ● 46 107 485SMDH 120L●71132Q 16 MTL/MEL 1 BXD02208IP to TRDR08IP11.00 1.5 SMDH 125S ● 28 91 20 2 0.75 12.5 ≤ D < 13.0 3 SMDH 125M ● 46 107 485SMDH 125L●71132Q 16 MTL/MEL 1 BXD02208IP to TRDR08IP11.00 1.5 SMDH 130S ● 30 92 20 2 0.75 13.0 ≤ D < 13.5 3 SMDH 130M ● 49 112 485SMDH 130L●76142Q 16 MTL/MEL 1 BXD02208IP to TRDR08IP11.00 1.5 SMDH 140S ● 34 96 20 2 3 SMDH 140M ● 55 119 1 0.75 13.5 ≤ D ≤ 14.5 5 SMDH 140L ● 84 149 48 Q 16 MTL/MEL 1 BXD02208IP to TRDR08IP 8 SMDH 140D ● 127 194 1 1.00 12 SMDH 140-12D ● 171 239 20 2 1.5 SMDH 150S ● 35 100 25 2 3 SMDH 150M ● 58 129 1 0.75 14.5 < D ≤ 15.5 5 SMDH 150L ● 89 159 50 Q 20 MTL/MEL 1 BXD02208IP to TRDR08IP 8 SMDH 150D ● 136 204 1 1.00 12 SMDH 150-12D ● 183 253 25 2 1.5 SMDH 160S ● 38 103 25 2 3 SMDH 160M ● 62 134 1 0.93 15.5 < D ≤ 16.5 5 SMDH 160L ● 95 169 50 Q 20 MTL/MEL 1 BXD02509IP to TRDR10IP 8 SMDH 160D ● 144 214 1 1.24 12 SMDH 160-12D ● 195 266 25 2 1.5 SMDH 170S ● 39 105 25 2 3 SMDH 170M ● 66 140 1 0.93 16.5 < D ≤ 17.5 5 SMDH 170L ● 101 175 50 Q 20 MTL/MEL 1 BXD02509IP to TRDR10IP 8 SMDH 170D ● 154 225 1 1.24 12 SMDH 170-12D ● 207 278 25 2 1.5 SMDH 180S ● 43 107 25 2 3 SMDH 180M ● 70 145 1 0.93 17.5 < D ≤ 18.5 5 SMDH 180L ● 107 180 50 Q 20 MTL/MEL 1 BXD02509IP to TRDR10IP 8 SMDH 180D ● 162 230 1 1.24 12 SMDH 180-12D ● 219 291 25 2 1.5 SMDH 190S ● 44 115 30 2 3 SMDH 190M ● 73 160 1 1.83 18.5 < D ≤ 19.5 5 SMDH 190L ● 112 195 56 Q 25 MTL/MEL 1 BXD03011IP to TRDR15IP 8 SMDH 190D ● 171 255 1 2.44 12 SMDH 190-12D ● 232 309 30 2 1.5 SMDH 200S ● 47 118 30 2 3 SMDH 200M ● 77 160 1 1.83 19.5 < D ≤ 20.5 5 SMDH 200L ● 118 200 56 Q 25 MTL/MEL 1 BXD03011IP to TRDR15IP 8 SMDH 200D ● 179 270 1 2.44 12 SMDH 200-12D ● 244 321 30 2 1.5 SMDH 210S ● 48 119 30 2 3 SMDH 210M ● 80 160 1 1.83 20.5 < D ≤ 21.5 5 SMDH 210L ● 123 200 56 Q 25 MTL/MEL 1 BXD03011IP to TRDR15IP 8 SMDH 210D ● 188 266 1 2.44 12 SMDH 210-12D ● 256 334 30 2 LU for 12D holder is the value with typical diameter. Recommended Cutting Conditions J95 MTL Type Head J96 MEL Type Head J98 J100 N m Recommended Tightening Torque (N·m)