Общий каталог Sumitomo 2019 - 2020 - страница 454

Milling CuttersFace MillingShoulde rMillingHigh FeedMulti-PurposeRadiusR / 3DProfilingGroove /T-SlotChamferingNon-ferrousMetalHigh-speedCast Iron ApplicationsFace MillingShoulder Milling Shank Dia. (mm) 11.37.5 12.7 9.312.6 12.7012.707.007.00 Axial Radial General–purpose Finishing Face Milling High Feed Shoulder Milling Groove Milling Ramping Chamfering Drilling Profiling Profile Finishing General Steel / Carbon Steel / Alloy Steel Tempered Steel / Die Steel Stainless Steel Cast Iron / Ductile Cast Iron Non–ferrous Metal Aluminum Alloy Ti Alloy / Heat–Resistant Alloy Hardened Steel MM ±0.013±0.013 Indexable Endmill Selection Guide G: Best S: Suitable H: Unsuitable Blank: Not Recommended Work Material Application P M K N S H Cutting Edge Angle Cutting Series Model Insert Rake / Edge Cat. No. Angle Maximum Depth of Cut Dia. / (mm) Diagram Cutting edge angle (Typical) 45 to 55 (Page) HRC DFC–E XNMU060608PNER–G H ø25 ø25totoø80ø42 DFC09000EDFCM09000E –5° –9° G S G S G G S G S →H106 11.2 UFO–E SFKN12T3AZTN * ø50 ø32 2.2 to to UFO4000E 27° –7° S S S S S S S S S S ø80 ø42 →H38 12.70 FPE SDKN42MT * ø50 ø32 2.0 to to FPE4000 15° –3° S S S S S S S ø80 ø42 →H41 12.70 ø14to ø16 to WEZ–E WEZ11000E AOMT11T302PEER–G 6° –7°REtoto ø80 ø32ø25ø25totoø80ø42 WEZ11000ELWEZ17000E 15° –18°6°–6° G G G G G→H62 WEZ17000EL12.8toto15° –12° G G G G G G G ø20to ø16 to WFX–Eø63ø32 WFX08000EWFXM08000E (For 12000 Type)SOMT120408PDER 12° –6° ø40to ø32ø80 S G G SWFX12000E→H96 WFXF12000E8°–8°12.7 G G G G G G ø16 ø16 TSX–E to toø80ø32ø20ø20toto TSX08000ETSXF08000E (For 08000 Type)LNEX080404PNER–G –36°to–20° ø80 ø32 ø25 ø25 –6° to to to G G G S G G G G G G G ø80 ø32 –3° ø32to TSX13000E 8.6TSXM13000E –31°to ø80 ø32ø40 TSXF13000E (For 13000 Type) –15°LNEX130604PNER–L to ø80 →H120 toto ø20to ø20 to TSXR–Eø40ø32ø40ø32toto TSXR08000ETSXR13000E –33°13–6° to –3° to –18° –23° to S G G G G G G G G ø50 ø42 →H128 –18° ø32to ø10 to WEX–Eø63ø20 WEX1000EWEX1000EL (For 2000 Type) 9° 7°AXMT123504PEER–Gtoto17° 17° ø14 ø16totoø63ø32 WEX2000EWEX2000EL 14° 10°toto S G G S G G G G G G G25° 18° ø25 ø20 WEX3000E(–C) RE 12.00 16° 8° to to WEX3000ES(–C) to to ø63 ø42 →H78 WEX3000EL 24° 15° to ø20to ø20 to WRX–E (For 2000 Type) 16° 13°WRX2000EAXMT123504PEER–Gtoto ø40 ø42ø40ø32 24°20° 16°12° S G G S G G G G G G G to to toø50ø42 WRX3000E→H86 RE 12.00 to to22° 13° ø16to ø16 to CHEø28ø25 TECN22R (IC=6.35) 6° –3°CHE2000TECN32R (IC=9.525)TEEN43R (IC=12.70)to15°to0° ø30 IC –3° to ø32 CHE3000 15° to S S S S S S S S ø40 0° ø50 ø32 2° to to CHE4000 M±0.013 15° to ø80 ø42 →H141 4° *Use a chamfering tool for chamfering operations. H10