Общий каталог Sumitomo 2019 - 2020 - страница 320

Grooving Tools CDX Grooving Insert TGA Type ( Coated Carbide / Cermet / Carbide / SUMIBORON / SUMIDIA) Fig 1 GAN CW ±0.025 Grade Cutting Edge GAN RE RE Coated Carbide AC530U Honing 15° IC Carbide H1 Sharp Edge 25° Coated Cermet T3000Z Honing 15° Cermet T1500A Sharp Edge 10° SUMIBORON BN2000 Negative Land 5° SUMIDIA DA2200 Sharp Edge 15° * For the rake angle when tted on the S holder, refer to page F5. Figure shows right hand (R) tool. Figure shows right hand (R) tool. F Square Edged Grooving Insert AC530U H1 T3000Z T1500A BN2000 DA2200 WidthCat. No.RLRLRLRLRLRLof CutCW Dimensions (mm)Maximum Depth of CutO.D.InternalDiameterMaximum GrooveDepth (mm)CDXNoseRadiusREInscribedCircleICThicknessS*GroupNo.Fig TGA R/L3033(E) D D D D D D D D Q Q Q Q 0.33 0.8 0.5 1.0 0.05 9.525 3.18 1 1 TGA R/L3050(E) D D D D D D D D Q Q Q Q 0.50 1.2 0.8 1.4 0.05 9.525 3.18 1 1 TGA R/L3075(E) D D D D D D D D 0.75 1 TGA R/L3095(E) D D D D D D D D 0.95 1 TGA R/L3100(E) D D D D D D D D 1.00 1 TGA R/L3110(E) D D D D D D 1.10 1 TGA R/L3125(E) D D D D D D D D 1.25 1 TGA R/L3135(E) D D D D D DTGA R/L3145(E)DDDDDDDD 1.35 2.0 1.5 2.5 *30.1 9.525 3.18 1 11.451 TGA R/L3150(E) D D D D D D D D 1.50 1 TGA R/L3165(E) D D D D D D 1.65 1 TGA R/L3175(E) D D D D D D 1.75 1 TGA R/L3185(E) D D D D D D D D 1.85 1 TGA R/L3200(E) D D D D D D D D 2.00 1 TGA R/L3220(E) D D D D D D 2.20 1 TGA R/L3230(E) D D D D D D D D 2.30 1 TGA R/L3250(E) D D D D D D D DTGA R/L3265(E)DDDDDD 2.50 2.5 2.0 3.0 *30.1 9.525 3.18 1 12.651 TGA R/L3270(E) D D D D D D 2.70 1 TGA R/L3280(E) D D D D D D 2.80 1 TGA R/L4125(E)TGA R/L4145(E) D D D D D D D D D DDDDDDDDD1.251.452.0 1.7 2.5 *20.2 12.70 4.76 2 11 TGA R/L4150(E) D D D D D D D D D D 1.50 1 TGA R/L4165(E) D D D D D D 1.65 1 TGA R/L4175(E) D D D D D D D D 1.75 1 TGA R/L4185(E)TGA R/L4200(E) D D D D D D D D 1.85 3.5 2.5 3.9 *20.2 12.70 4.76 3 1DDDDDDDDDD2.001 TGA R/L4220(E) D D D D D D 2.20 1 TGA R/L4230(E) D D D D D D D D 2.30 1 TGA R/L4250(E) D D D D D D D D D D 2.50 1 TGA R/L4265(E) D D D D D D D DTGA R/L4270(E)DDDDDD 2.65 *15.0 2.5 *15.4 *20.3 12.70 4.76 4 12.701 TGA R/L4280(E)TGA R/L4300(E) D D D D D D D DDDDDDDDDD D 2.80 *13.005.02.5 *15.4 *20.3 12.70 4.76 4 11 TGA R/L4320(E) D D D D D DTGA R/L4330(E)DDDDDDDD 3.203.30 *15.0 2.5 5.4 *20.3 12.70 4.76 4 11 TGA R/L4350(E) D D D D D D D D D D 3.50 1 TGA R/L4370(E) D D D D D D 3.70TGA R/L4390(E)DDDDDD3.90 *20.3 11 TGA R/L4400(E) D D D D D D D D D D 4.00 1 TGA R/L4410(E) D D D D D DTGA R/L4420(E)DDDDDD 4.10 5.04.20 2.5 5.4 12.70 4.76 4 11 TGA R/L4430(E) D D D D D D D D 4.30TGA R/L4440(E)DDDDDD4.40 *20.4 11 TGA R/L4450(E) D D D D D D D D 4.50 1 TGA R/L4480(E) D D D D D D D D 4.80 5.00 1 * Add E as the part number suffix for T1500A. * Refer to pages F4 and F5 for group numbers of holders that can be used with the GWC, GWCS and GWCI types. Select applicable inserts for the holders by using matching group numbers. *1: CDX = 4.4 (maximum groove depth 4.0) for SUMIBORON and SUMIDIA (2.5 for internal diameter machining) *2: RE = 0.2 for SUMIBORON; RE = 0.1 for SUMIDIA *3: T1500A is RE = 0.2 F6