Общий каталог Sumitomo 2019 - 2020 - страница 264

SEC-Boring Bar S-DWLN / D-DWLN Type Medium Diameter General-purpose 95° Steel Double Clamp S-DWLN Fig 1 DMIN Min. Bore Dia. DCON Fig 2 DMIN Min. Bore Dia. DCON Bottom Facing 95° 95° Boring WF WF Bars H -12° H LF LF -6° GAMF GAMF -6° -6° E Holder LHD Figure shows right-hand (R) tool. Parts Dimensions (mm) Shim Upper Surface Lower Surface Stock Min. Overall Cutting Rake Applicable Insert Clamp Set Shim Screw Wrench Wrench Material Bore Diameter Height Edge Head Holder C Cat. No. Length Angle Fig Dia. Distance Ref. Page R L Cat. No. Nm DMIN DCON H LF WF LHD GAMF (For Hex Socket) (For Hex Socket) S32S-DWLN R/L0604-40 ● ● 40 32 30 250 22.0 29 -10° WN□□0604 B69 on 1 SCP-4 5.0 WNS0603B BFTX0307N LH040 LH025 D S25R-DWLN R/L0804-32 ● ● 32 25 23 200 17.0 26 -12° 1 WNS0803B BFTX0307N Steel S32S-DWLN R/L0804-40 ● ● 40 32 30 250 22.0 26 -12° 1 WN□□0804 B71 on SCP-2 5.0 LH040 LH025 S40T-DWLN R/L0804-50 ● ● 50 40 37 300 27.0 26 -12° 1 WNS0804B BFTX0409N S50U-DWLN R/L0804-63 ● ● 63 50 47 350 31.5 Q -12° 2 Feed direction of applicable inserts differs according to machining details. (Refer to * note below) Clamp Set Parts E70 R Steel with 95° Anti-Vibration Medium Diameter General-purpose Mechanism S Coolant Hole Double Clamp D-DWLN Fig 1 DMIN Min. Bore Dia. With oil hole DCON Bottom Facing T 95° WF H LF GAMF V -6° LHD Figure shows right-hand (R) tool. W Holder Parts Dimensions (mm) Shim Upper Surface Lower Surface Stock Min. Overall Cutting Rake Applicable Insert Clamp Set Shim Materials Screw Wrench Wrench Holders Bore Diameter Height Edge Head Very Small Diameter Turning Cat. No. Length Angle Fig Small Diameter Turning Dia. Distance Ref. Page R L Cat. No. Nm DMIN DCON H LF WF LHD GAMF (For Hex Socket) (For Hex Socket) Steel with Oil Hole D25T-DWLN R/L0804-32 ● ● 32 25 23 300 17 26 -12° 1 WNS0803B BFTX0307N B71 with Anti-Vibration D32T-DWLN R/L0804-40 ● ● 40 32 30 300 22 26 -10° WN□□0804 1 SCP-2 5.0 LH040 LH025 on WNS0804B BFTX0409N Mechanism D40U-DWLN R/L0804-50 ● ● 50 40 37 350 27 26 -10° 1 Feed direction of applicable inserts differs according to machining details. (Refer to * note below) Clamp Set Parts E70 *Applicable Inserts for DWLN Type For internal diameter machining: Right-handed (R) tool holders are compatible with left-handed (L) or neutral (N) inserts. Left-handed (L) tool holders are compatible with right-handed (R) or neutral (N) inserts. For facing: Right-handed (R) tool holders are compatible with right-handed (R) or neutral (N) inserts. Left-handed (L) tool holders are compatible with left-handed (L) or neutral (N) inserts. E20 N m Recommended Tightening Torque (N·m)