Solid Carbide Spiral Endmills Solid Carbide Spiral Endmills
SSM 2000 Type (ø8,6~ø30) SSM 4000 Type (ø1,5~ø25)
Carbide grade: A1 (Micrograin) Carbide grade: A1 (Micrograin)
| Helix angle : 30˚ | øD | | Tolerance (mm) | Helix angle : 30˚ | øD | | | Tolerance (mm) |
| Corner : Sharp edge | | 6,0 < D ≤ 10,0 | – 0,015 – 0,040 | Corner : Sharp edge | | | D ≤ 6,0 | – 0,010 – 0,030 |
| | 10,0 < D | – 0,020 – 0,050 | | | 6,0 < D ≤ 10,0 | | – 0,015 – 0,040 |
10,0 < D – 0,020 – 0,050
| Endmills | | | | | (mm) |
| Cat. No. | Stock | øD | l | L | ød |
| SSM 2086 | m | 8,6 | 15 | 55 | 10 |
| SSM 2087 | | 8,7 | 15 | 55 | 10 |
| SSM 2088 | | 8,8 | 15 | 55 | 10 |
| SSM 2089 | | 8,9 | 15 | 55 | 10 |
| SSM 2090 | l | 9,0 | 15 | 55 | 10 |
| SSM 2091 | | 9,1 | 15 | 55 | 10 |
| SSM 2092 | | 9,2 | 15 | 55 | 10 |
| SSM 2093 | | 9,3 | 15 | 55 | 10 |
| SSM 2094 | | 9,4 | 15 | 55 | 10 |
| SSM 2095 | | 9,5 | 15 | 55 | 10 |
| SSM 2096 | | 9,6 | 18 | 65 | 10 |
| SSM 2097 | | 9,7 | 18 | 65 | 10 |
| SSM 2098 | | 9,8 | 18 | 65 | 10 |
| SSM 2099 | | 9,9 | 18 | 65 | 10 |
| SSM 2100 | l | 10,0 | 18 | 65 | 10 |
| SSM 2105 | q | 10,5 | 18 | 70 | 12 |
| SSM 2110 | l | 11,0 | 18 | 70 | 12 |
| SSM 2115 | l | 11,5 | 18 | 70 | 12 |
| SSM 2120 | l | 12,0 | 18 | 70 | 12 |
| SSM 2125 | | 12,5 | 20 | 80 | 16 |
| 2 SSM 2130 | l | 13,0 | 20 | 80 | 16 |
| SSM 2135 | | 13,5 | | 80 | 16 |
| SSM 2140 | l | 14,0 | 20 | 80 | 16 |
| SSM 2145 | | 14,5 | 25 | 80 | 16 |
| SSM 2150 | l | 15,0 | 25 | 80 | 16 |
| SSM 2155 | | 15,5 | 35 | 90 | 16 |
| SSM 2160 | l | 16,0 | 35 | 90 | 16 |
| SSM 2165 | | 16,5 | 35 | 90 | 20 |
| SSM 2170 | l | 17,0 | 35 | 90 | 20 |
| SSM 2175 | | 17,5 | 40 | 105 | 20 |
| SSM 2180 | l | 18,0 | 40 | 105 | 20 |
| SSM 2185 | | 18,5 | 40 | 105 | 20 |
| SSM 2190 | | 19,0 | 40 | 105 | 20 |
| SSM 2195 | | 19,5 | 40 | 105 | 20 |
| SSM 2200 | l | 20,0 | 40 | 105 | 20 |
| SSM 2210 | l | 21,0 | 40 | 105 | 25 |
| SSM 2220 | l | 22,0 | 40 | | 25 |
| SSM 2230 | l | | 45 | 115 | 25 |
| SSM 2240 | | 24,0 | 45 | 115 | 25 |
| SSM 2250 | l | | 50 | | 25 |
| SSM 2300 | | | 55 | 130 | 32 |
| En | dmills | | | | | (mm) |
| Cat. No. | Stock | øD | l | L | ød |
| SSM 4015 | l | 1,5 | 5 | 40 | 4 |
| SSM 4020 | l | 2,0 | 6 | 40 | 4 |
| SSM 4025 | l | 2,5 | 8 | 40 | 4 |
| SSM 4030 | l | 3,0 | 8 | 45 | 6 |
| SSM 4035 | l | 3,5 | 8 | 45 | 6 |
| SSM 4040 | l | 4,0 | 10 | 45 | 6 |
| SSM 4045 | l | 4,5 | 10 | 45 | 6 |
| SSM 4050 | l | 5,0 | 12 | 50 | 6 |
| SSM 4055 | l | 5,5 | 12 | 50 | 6 |
| SSM 4060 | l | 6,0 | 12 | 50 | 6 |
| SSM 4065 | l | 6,5 | 12 | 50 | 8 |
| SSM 4070 | l | 7,0 | 15 | 55 | 8 |
| SSM 4075 | l | 7,5 | 15 | 55 | 8 |
| SSM 4080 | l | 8,0 | 15 | 55 | 8 |
| SSM 4085 | l | 8,5 | 15 | 55 | 10 |
| SSM 4090 | l | 9,0 | 15 | 55 | 10 |
| 4 | SSM 4095 | l | 9,5 | 15 | 55 | 10 |
| SSM 4100 | l | 10,0 | 18 | 65 | 10 |
| SSM 4105 | | 10,5 | 18 | 65 | 12 |
| SSM 4110 | l | 11,0 | 18 | 70 | 12 |
| SSM 4120 | l | 12,0 | 18 | 70 | 12 |
| SSM 4130 | | 13,0 | 20 | 80 | 16 |
| SSM 4140 | l | 14,0 | 20 | 80 | 16 |
| SSM 4150 | l | 15,0 | 25 | 80 | 16 |
| SSM 4160 | l | 16,0 | 35 | 90 | 16 |
| SSM 4170 | q | 17,0 | 35 | 90 | 20 |
| SSM 4180 | l | 18,0 | 40 | 105 | 20 |
| SSM 4190 | | 19,0 | 40 | 105 | 20 |
| SSM 4200 | l | 20,0 | 40 | 105 | 20 |
| SSM 4210 | | 21,0 | 40 | 105 | 25 |
| SSM 4220 | | 22,0 | 40 | 105 | 25 |
| SSM 4230 | | 23,0 | 45 | 115 | 25 |
| SSM 4240 | | 24,0 | 45 | 115 | 25 |
| SSM 4250 | l | 25,0 | 50 | 120 | 25 |
| Mat | erial | Carb | on steel,Alloy | steel | Cast iron | |
| øD | | (BelowHRC30) | (BelowHRC40) | (BelowHRC45) | | |
| 1 ~ | vc | 40-50-60 | 30-40-50 | 20-30-40 | 40-50-60 | |
| 2,9 | ft | 0,004~0,017 | 0,004~0,017 | 0,002~0,008 | 0,008~0,020 | |
| 3 ~ | vc | 40-50-60 | 30-40-50 | 20-30-40 | 40-50-60 | |
| 5,9 | ft | 0,018~0,036 | 0,018~0,036 | 0,009~0,018 | 0,027~0,060 | |
| 6 ~ | vc | 40-50-60 | 30-40-50 | 20-30-40 | 40-50-60 | |
| 12,9 | ft | 0,038~0,070 | 0,038~0,070 | 0,019~0,035 | 0,065~0,157 | doc |
| 13 ~ | vc | 40-50-60 | 30-40-50 | 20-30-40 | 40-50-60 | |
| 19,9 | ft | 0,075~0,125 | 0,075~0,125 | 0,040~0,075 | 0,160~0,250 | øD |
| 20 ~ | vc ft vc= | 40-50-60 0,135~0,170 m/min ft=m | 30-40-50 0,135~0,170 m/tooth | 20-30-40 0,085~0,110 | 40-50-60 0,257~0,390 | woc |
Общий каталог Sumitomo 2012
Каталог Sumitomo резьбонарезной инструмент
Каталог Sumitomo пластины с режущей кромкой-моноалмаз Sumicristal
Каталог Sumitomo инструмент для обработки канавок
Общий каталог Sumitomo 2019 - 2020
Каталог Sumitomo запасные части