Общий каталог SGS 2021 - страница 32

FRACTIONAL Z-Carb-HPR 37° POS 5 TOLERANCES (inch) ≠ 1/8–1/4 DIAMETER DC = +0.0000/–0.0012 DCON = h 6 RE = +0.0000/–0.0020 >1/4–3/8 DIAMETER DC = +0.0000/–0.0016 LF APMX DCON = h 6 RE = +0.0000/–0.0020 Z5 • DC DCON >3/8–1 DIAMETER Z5CR DC = +0.0000/–0.0020 NCD DCON = h 6 FRACTIONAL SERIES RE RE = +0.0000/–0.0020 inch EDP NO. CONTINUED NON- CUTTING TI-NAMITE-A TI-NAMITE-M • An ideal balance of helix, CUTTING LENGTH OVERALL SHANK CORNER CENTER TI-NAMITE-A TI-NAMITE-A (TA) TI-NAMITE-M TI-NAMITE-M (TM) indexing, flute depth, DIAMETER OF CUT LENGTH DIAMETER RADIUS DIAMETER (TA) (TA) W/INTERNAL (TM) (TM) W/INTERNAL rake and relief DC APMX LF DCON RE NCD W/FLAT COOLANT W/ FLAT COOLANT • Variable indexing for 3/4 2 4-1/2 3/4 0.120 0.2630 37236 – – 37237 – – chatter supression and patented edge geometry 1 1-1/8 4 1 – 0.3500 38510 38516 38522 37116 37123 37288 for shearing and strength 1 1-1/8 4 1 0.010 0.3500 38869 38871 38873 38868 38870 38872 • Chatter-free geometry allows deep cutting and 1 1-1/8 4 1 0.030 0.3500 38563 38608 38647 37117 37124 37289 high speed machining 1 1-1/8 4 1 0.060 0.3500 38564 38609 38648 37118 37125 37290 • Central coolant hole delivers coolant 1 1-1/8 4 1 0.090 0.3500 38565 38610 38649 37119 37126 37291 effectively to the cutting zone enhancing chip 1 1-1/8 4 1 0.120 0.3500 38566 38611 38650 37120 37127 37292 removal when pocketing or slotting 1 1-1/8 4 1 0.190 0.3500 38567 38612 38651 37121 37128 37293 • Excels at roughing, 1 1-1/8 4 1 0.250 0.3500 38568 38613 38652 37122 37129 37294 ramping, high speed machining and finishing 1 1-1/2 4 1 – 0.3500 37214 37218 38523 37130 37137 37295 in a variety of materials 1 1-1/2 4 1 0.010 0.3500 38875 38877 38879 38874 38876 38878 • Enhanced corner geometry with tight 1 1-1/2 4 1 0.030 0.3500 37215 37219 38653 37131 37138 37296 tolerance corner radii 1 1-1/2 4 1 0.060 0.3500 37216 37220 38654 37132 37139 37297 • Recommended for materials ≤ 45 HRc 1 1-1/2 4 1 0.090 0.3500 38569 38614 38655 37133 37140 37298 (≤ 420 Bhn) 1 1-1/2 4 1 0.120 0.3500 37217 37221 38656 37134 37141 37299 1 1-1/2 4 1 0.190 0.3500 38570 38615 38657 37135 37142 37300 1 1-1/2 4 1 0.250 0.3500 38571 38616 38658 37136 37143 37301 STEELS 1 2 4-1/2 1 – 0.3500 38511 38517 38524 37144 37151 37302 STAINLESS STEELS 1 2 4-1/2 1 0.010 0.3500 38881 38883 38885 38880 38882 38884 CAST IRON 1 2 4-1/2 1 0.030 0.3500 38572 38617 38659 37145 37152 37303 HIGH TEMP ALLOYS 1 2 4-1/2 1 0.060 0.3500 38573 38618 38660 37146 37153 37304 TITANIUM 1 2 4-1/2 1 0.090 0.3500 38574 38619 38661 37147 37154 37305 HARDENED STEELS 1 2 4-1/2 1 0.120 0.3500 38575 38620 38662 37148 37155 37306 1 2 4-1/2 1 0.190 0.3500 38576 38621 38663 37149 37156 37307 For patent 1 2 4-1/2 1 0.250 0.3500 38577 38622 38664 37150 37157 37308 information visit www.ksptpatents.com 32 END MILLS END MILLS www.kyocera-sgstool.com