Общий каталог SGS 2018 - страница 34

FRACTIONAL Z-Carb-AP 4 ≠ ≠ Z1PCR TOLERANCES (inch) <1/8 DIAMETER FRACTIONAL SERIES D1 = +0.0005/–0.0005 • Variable rake geometry inch EDP NO. D2 = h6 alters and controls the CUTTING LENGTH OVERALL SHANK CORNER Ti-NAMITE-X Ti-NAMITE-X JetStream cutting dynamic taking DIAMETER OF CUT LENGTH DIAMETER RADIUS W/FLAT R = +0.000/–0.0010 chatter suppression to an D1 L2 L1 D2 R unprecedented level 1/8–1/4 DIAMETER 1/64 1/32 1-1/2 1/8 .002 36874 – – D1 = +0.000/–0.0012 • Unequal helix design changes the cutting 1/32 5/64 1-1/2 1/8 .005 36875 – – D2 = h6 angle to improve 3/64 7/64 1-1/2 1/8 .005 36876 – – R = +0.000/–0.0020 harmonics • Unequal flute spacing 1/16 3/16 1-1/2 1/8 .005 36872 – – >1/4–3/8 DIAMETER helps to disrupt the 5/64 3/16 1-1/2 1/8 .005 36877 – – D1 = +0.000/–0.0016 rhythmic pattern created 3/32 9/32 1-1/2 1/8 .010 36873 – – D2 = h6 by the cutting edge helping to suppress R = +0.000/–0.0020 7/64 3/8 1-1/2 1/8 .010 36878 – – damaging harmonics 1/8 3/8 1-1/2 1/8 .010 36370 – – >3/8–1 DIAMETER • Enhanced corner geometry with tight 1/8 3/8 1-1/2 1/8 .015 36851 – – D1 = +0.000/–0.0020 tolerance corner radii D2 = h6 3/16 7/16 2 3/16 .010 36371 – – • Recommended for R = +0.000/–0.0020 materials ≤ 45 HRc 3/16 7/16 2 3/16 .015 36852 – – (≤ 420 Bhn) 3/16 7/16 2 3/16 .030 36722 – – STEELS 1/4 1/2 2-1/2 1/4 .010 36372 – – 1/4 1/2 2-1/2 1/4 .015 36723 – – STAINLESS STEELS 1/4 1/2 2-1/2 1/4 .020 36853 – – CAST IRON 1/4 1/2 2-1/2 1/4 .030 36373 – – HIGH TEMP ALLOYS 1/4 3/4 2-1/2 1/4 .010 36599 – – TITANIUM 1/4 3/4 2-1/2 1/4 .015 36600 – – 1/4 3/4 2-1/2 1/4 .020 36854 – – HARDENED STEELS 1/4 3/4 2-1/2 1/4 .030 36601 – – 5/16 13/16 2-1/2 5/16 .015 36724 – – For patent 5/16 13/16 2-1/2 5/16 .020 36855 – – information visit www.ksptpatents.com 5/16 13/16 2-1/2 5/16 .030 36374 – – 3/8 7/8 2-1/2 3/8 .010 36375 36701 – 3/8 7/8 2-1/2 3/8 .015 36725 36736 – 3/8 7/8 2-1/2 3/8 .020 36856 36864 – 3/8 7/8 2-1/2 3/8 .030 36376 36702 – 3/8 7/8 2-1/2 3/8 .060 36727 36738 – continued on next page 34 END MILLS END MILLS www.kyocera-sgstool.com