Общий каталог Osawa 2018

Общий каталог Osawa 2021

CUTTING PARAMETERS

INFO HF443

	Material Group ISO 513	P1	P2 M1	K1	P3	P4 M2 K2	K3	P5 M3	M4 K4	S1 S4		S2 S3 S5
	Hardness/Rm	≤	700 N/mm	²	70	0-1000 N/m	m²		≤ 35 HRC			≤ 40 HRC
	ap x ae		DxD			DxD			0.5D x D			0.5D x D
	Vc (m/min)		85-105			55-75			40-60			20-40
	D	n	fz	Vf	n	fz	Vf	n	fz	Vf	n	fz	Vf
	(mm)	(rpm)	(mm/z)	(mm/min)	(rpm)	(mm/z)	(mm/min)	(rpm)	(mm/z)	(mm/min)	(rpm)	(mm/z)	(mm/min)
	3	10080	0.006	250	6900	0.006	160	5310	0.005	110	3180	0.007	90
DRILLING	4	7560	0.008	250	5180	0.007	160	3980	0.007	110	2390	0.009	90
	5	6050	0.010	250	4140	0.009	150	3180	0.008	110	1910	0.011	90
	6	5040	0.012	240	3450	0.011	150	2650	0.010	100	1590	0.013	90
	8	3780	0.016	240	2590	0.014	150	1990	0.013	100	1190	0.017	80
	10	3030	0.019	230	2070	0.017	140	1590	0.015	100	960	0.021	80
	12	2520	0.022	220	1730	0.019	130	1330	0.017	90	800	0.024	80
	14	2160	0.024	210	1480	0.022	130	1140	0.019	90	680	0.027	70
	16	1890	0.027	200	1290	0.024	130	1000	0.022	90	600	0.030	70
	20	1510	0.033	200	1040	0.030	120	800	0.026	80	480	0.036	70
ap x ae	≤ D5		0.5D x D			0.5D x D			0.25D x D			0.25D x D
	Material Group ISO 513	P1	P2 M1	K1	P3	P4 M2 K2	K3	P5 M3	M4 K4	S1 S4		S2 S3 S5
	Hardness/Rm	≤	700 N/mm	²	70	0-1000 N/m	m²		≤ 35 HRC			≤ 40 HRC
	ap x ae		2D x 0.2D			2D x 0.1D			1.5D x 0.1D			1.5D x 0.1	D
	Vc (m/min)		160-200			110-130			80-100			50-70
	D	n	fz	Vf	n	fz	Vf	n	fz	Vf	n	fz	Vf
	(mm)	(rpm)	(mm/z)	(mm/min)	(rpm)	(mm/z)	(mm/min)	(rpm)	(mm/z)	(mm/min)	(rpm)	(mm/z)	(mm/min)
	3	10080	0.032	1270	6900	0.028	780	5310	0.025	540	3180	0.035	440
TROCHOIDAL	4	7560	0.042	1260	5180	0.037	780	3980	0.033	530	2390	0.046	440
	5	6050	0.052	1250	4140	0.047	770	3180	0.041	530	1910	0.057	430
	6	5040	0.061	1220	3450	0.055	750	2650	0.049	520	1590	0.067	430
	8	3780	0.079	1190	2590	0.071	730	1990	0.063	500	1190	0.087	410
	10	3030	0.095	1150	2070	0.085	700	1590	0.076	480	960	0.104	400
	12	2520	0.108	1090	1730	0.097	670	1330	0.086	460	800	0.119	380
	14	2160	0.122	1050	1480	0.109	650	1140	0.097	440	680	0.134	360
	16	1890	0.135	1020	1290	0.122	630	1000	0.108	430	600	0.149	360
	20	1510	0.164	990	1040	0.148	610	800	0.131	420	480	0.181	350
ap x ae	≤ D5		1.5D x 0.1D			1.5D x 0.1D

PU-HPU

SUH

ALH

TYPHOON

SUH MINI

TYPHOON HL

C-SD-TA

HSS-HSS/CO

NOTES: HF VH/UP Down milling CNC programming is required. “ae” value max 0.2xD - “T” value max 0.1xD. The use of end mill with diameter 30-40% smaller than the width of the slot is recommended. The cutting conditions are based on CNC programming with medium dynamic speed. MEF With lower CNC dynamic speed, use the same cutting conditions or reduce the cutting speed Vc. With higher CNC dynamic speed, reduce the “T” value by approximately -30 -50% and apply the maximum available cutting speed Vc. R1 Cutter radius ae ALU R2 Half of slot width T Programming width of cut ae Actual width of cut MEX Y (+) Y UH X (+)

T HSS/CO-HSSP END MILLS

CARBIDE

Общий каталог Osawa 2018 - страница 436

Навигация

CUTTING PARAMETERS

Общий каталог Osawa 2018 - страница 436

Навигация

CUTTING PARAMETERS

Отправьте заявку

На подбор необходимой оснастки и оборудования