HF UNI - Variable Helix and unequal pitch - Corner radius CUTTING PARAMETERS HF442 INFO Material Group P1 P2 M1 K1 P3 P4 M2 K2 K3 P5 M3 M4 K4 S1 S4 S2 S3 S5 TTYAP-HHTOAO-4NHTA ISO 513 Hardness/Rm ≤ 700 N/mm² 700-1000 N/mm² ≤ 35 HRC ≤ 40 HRC TPYUP-HHPOUON ap x ae 2D x 0.2D 2D x 0.1D 1.5D x 0.1D 1.5D x 0.1D Vc (m/min) 160-200 110-130 80-100 50-70 D n fz Vf n fz Vf n fz Vf n fz Vf TSUYPHHOON (mm) (rpm) (mm/z) (mm/min) (rpm) (mm/z) (mm/min) (rpm) (mm/z) (mm/min) (rpm) (mm/z) (mm/min) 3 10080 0.032 1270 6900 0.028 780 5310 0.025 540 3180 0.035 440 TROCHOIDAL 4 7560 0.042 1260 5180 0.037 780 3980 0.033 530 2390 0.046 440 TAYLPHHOON 5 6050 0.052 1250 4140 0.047 770 3180 0.041 530 1910 0.057 430 6 5040 0.061 1220 3450 0.055 750 2650 0.049 520 1590 0.067 430 8 3780 0.079 1190 2590 0.071 730 1990 0.063 500 1190 0.087 410 10 3030 0.095 1150 2070 0.085 700 1590 0.076 480 960 0.104 400 THYRPCHOON 12 2520 0.108 1090 1730 0.097 670 1330 0.086 460 800 0.119 380 14 2160 0.122 1050 1480 0.109 650 1140 0.097 440 680 0.134 360 16 1890 0.135 1020 1290 0.122 630 1000 0.108 430 600 0.149 360 TSUYPHHMOIONIN 20 1510 0.164 990 1040 0.148 610 800 0.131 420 480 0.181 350 ap x ae ≤ D5 1.5D x 0.1D 1.5D x 0.1D NOTES: THYLPHOON Down milling CNC programming is required. “ae” value max 0.2xD - “T” value max 0.1xD. The use of end mill with diameter 30-40% smaller than the width of the slot is recommended. C-SD-TA The cutting conditions are based on CNC programming with medium dynamic speed. With lower CNC dynamic speed, use the same cutting conditions or reduce the cutting speed Vc. With higher CNC dynamic speed, reduce the “T” value by approximately -30 -50% and apply the maximum available cutting speed Vc. R1 Cutter radius LFTA ae R2 Half of slot width T Programming width of cut R2 ae Actual width of cut SUTA R1 Y (+) Y HDSRSIL-LHSSS/CO X (+) G2 T MDTA HF VH/UP MEF ALU MEX UH HENSSD/CMOIL-LHSSSP CBUARRRBSIDE PARAMETERS SUGGESTED WITH HIGH POWER MILLING CHUCK AND STABLE MACHINING CONDITION 429