Общий каталог Osawa 2018

Общий каталог Osawa 2021

CUTTING PARAMETERS

INFO HF444

	Material Group ISO 513	P1	P2 M1	K1	P3	P4 M2 K2	K3	P5 M3	M4 K4	S1 S4		S2 S3 S5
	Hardness/Rm	≤	700 N/mm	²	70	0-1000 N/m	m²		≤ 35 HRC			≤ 40 HRC
	ap x ae		D x 0.4D			D x 0.4D			D x 0.25D			D x 0.25D
	Vc (m/min)		100-120			60-80			45-65			30-40
	D (mm)	n (rpm)	fz (mm/z)	Vf (mm/min)	n (rpm)	fz (mm/z)	Vf (mm/min)	n (rpm)	fz (mm/z)	Vf (mm/min)	n (rpm)	fz (mm/z)	Vf (mm/min)
VERTICAL	6	5840	0.026	610	3720	0.024	350	2920	0.020	230	1860	0.018	140
	8	4380	0.034	600	2790	0.031	340	2190	0.026	220	1390	0.024	130
	10	3500	0.041	570	2230	0.037	330	1750	0.031	210	1110	0.029	130
	12	2920	0.047	540	1860	0.042	310	1460	0.035	200	930	0.033	120
	14	2500	0.052	520	1590	0.047	300	1250	0.039	200	800	0.037	120
	16	2190	0.058	510	1390	0.052	290	1090	0.044	190	700	0.041	110
	20	1750	0.071	500	1110	0.064	280	880	0.053	190	560	0.050	110

PU-HPU

ALH

TYPHOON

Material Group ISO 513	P1	P2 M1	K1	P3	P4 M2 K2	K3	P5 M3	M4 K4	S1 S4		S2 S3 S	5
Hardness/Rm	≤	700 N/mm	²	70	0-1000 N/m	m²		≤ 35 HRC			≤ 40 HRC
ap x ae		2D x 0.2D			2D x 0.1D		1	.5D x 0.1D			1.5D x 0.1	D
Vc (m/min)		160-200			110-130			80-100			50-70
D	n	fz	Vf	n	fz	Vf	n	fz	Vf	n	fz	Vf
(mm)	(rpm)	(mm/z)	(mm/min)	(rpm)	(mm/z)	(mm/min)	(rpm)	(mm/z)	(mm/min)	(rpm)	(mm/z)	(mm/min)
6	5040	0.066	1320	3450	0.059	810	2650	0.052	560	1590	0.072	460
8	3780	0.085	1290	2590	0.077	790	1990	0.068	540	1190	0.094	450
10	3030	0.102	1240	2070	0.092	760	1590	0.082	520	960	0.112	430
12	2520	0.117	1180	1730	0.105	730	1330	0.093	500	800	0.128	410
14	2160	0.131	1130	1480	0.118	700	1140	0.105	480	680	0.144	390
16	1890	0.146	1100	1290	0.131	680	1000	0.117	470	600	0.160	380
20	1510	0.177	1070	1040	0.160	660	800	0.142	450	480	0.195	370

TYPHOON HL

TROCHOIDAL

LFTA

HSS-HSS/CO NOTES: DRILLS Down milling CNC programming is required. “ae” value max 0.2xD - “T” value max 0.1xD. The use of end mill with diameter 30-40% smaller than the width of the slot is recommended. G2 The cutting conditions are based on CNC programming with medium dynamic speed. With lower CNC dynamic speed, use the same cutting conditions or reduce the cutting speed Vc. With higher CNC dynamic speed, reduce the “T” value by approximately -30 -50% and apply the maximum available cutting speed Vc. R1 Cutter radius MDTA ae R2 Half of slot width T Programming width of cut ae Actual width of cut HF VH/UP

Y (+) Y MEF X (+)

ALU T

MEX

HSS/CO-HSSP END MILLS

CARBIDE

Общий каталог Osawa 2018 - страница 414

Навигация

CUTTING PARAMETERS

Общий каталог Osawa 2018 - страница 414

Навигация

CUTTING PARAMETERS

Отправьте заявку

На подбор необходимой оснастки и оборудования