| ■ 55° Rhombic / Positive with Hole | Insert Description | Ref. to Page for Applicable Toolholders Description | A | T φd | α |
| DC..07 type | E24~E27,E35,F43~F45 DC_0702_ | 6.35 2.38 | 2.8 | 7° |
| B | DC..11 type | E20,E24~E27,E35,F43~F45,F65 DC_11T3_ 9.525 3.97 | | 4.4 | 7° |
| | | Q | | Free-cutting steel |
| P | | | | | |
| rH | N O N | QP | P P | | Carbon Steel / Alloy Steel |
| M | | PQ | QPP | | Stainless Steel |
| | | | | Gray Cast Iron |
| K | | | | | |
| | | | | Nodular Cast Iron |
| Chipbreakers N | | | | Q | Non-ferrous Metals |
| D | | | Q | | Heat-resistant Alloys |
| T 55° Positive S | | | | | |
| | | Q | P | Titanium Alloys |
| H | | | | | Hard Materials |
| Dimension | | PVD MEGACOAT | PVD Coated | | |
| Cermet MEGACOAT Coated | CVD Coated Carbide | | | |
| (mm) | Cermet | Cermet MEGACOAT NANO | Carbide DLC Carbide | | |
| Description Insert | | | | | |
| re | | | | | |
| Handed Insert | TN6010 TN6020 TN60 TN610 TN620 PV710 PV720 | CA510 CA515 CA525 CA530 PV90 PV7020 PV7010 PV7025 PV7005 | PR930 PR1005 PR1025 PR1125 | KW10 SW05 | |
| | | CA5505 CA5515 CA5525 CA5535 CA6515 CA6525 CA4505 CA4515 | CA4010 CA4115 CA4120 | PR1425 PR1225 PR1305 PR1310 PR1325 | |
| shows Left-hand | | | | | | |
| DCET 11T3003FR-JSF 0.03 | | | | N | |
| Super Fine | | | | | | |
| | 11T3003FL-JSF 0.03 | | | | N |
| 11T301FR-JSF | 0.1 | | | N |
| 11T301FL-JSF | 0.1 | | | N |
| 11T302FR-JSF | 0.2 | N | | N |
| 11T302FL-JSF | 0.2 | | | N |
| DCET 11T3005MFR-JSF <0.05 | | | | N N | |
| Ceramic 11T3005MFL-JSF <0.05 | | N | | |
| 11T301MFR-JSF | <0.1 | N | | N |
| 11T301MFL-JSF | <0.1 | N | | U |
| 11T302MFR-JSF | <0.2 | N | | N |
| 11T302MFL-JSF | <0.2 | N | | N |
| Sharp Edge / Precision | | | | |
| DCET 0702005MFR-J <0.05 | | N N N | | |
| 1(: | | | | |
| 070201MFR-J | <0.1 | N N | N | |
| 070201MFL-J | <0.1 | N N | N | |
| 070202MFR-J | <0.2 | N N | N | |
| 070202MFL-J | <0.2 | N N | N | |
DCET 11T3005MFR-J <0.05 N N 1
| 11T301MFR-J | <0.1 N | | N | N | N | | | |
| 11T301MFL-J | <0.1 N | | N | N | N | | | |
| 11T302MFR-J | <0.2 N | | N | N | N | | | |
| 11T302MFL-J | <0.2 N | | N | N | N | | | |
| 11T304MFR-J | <0.4 | | | N | N | | | |
| Sharp Edge | | | | | | | | |
| DCGT 11T3003FR-J | 0.03 | | | N | | | | |
| 11T301FR-J | 0.1 | N | N | | | N | | N |
| 11T301FL-J | 0.1 | N | | | | N | | N |
| 11T302FR-J | 0.2 | N | N | | | N | | N |
| 11T302FL-J | 0.2 | N | N | | | N | | N |
| DCGT 11T3005MFR-J <0.05 | | | | N | | | N | |
| 11T3005MFL-J <0.05 | | | | N | | | | |
| 11T301MFR-J | <0.1 | | | N | | | N N | |
| 11T301MFL-J | <0.1 | | | N | | | U | |
| 11T302MFR-J | <0.2 | | | N | | | N N | |
| 11T302MFL-J | <0.2 | | | N | | | N | |
| 11T304MFR-J | <0.4 | | | N | | | N N | |
| 11T304MFL-J | <0.4 | | | N | | | N N | |
Sharp Edge
- Insert whose corner-R(re) dimension expressed with less than sign (e.g. < 0.05, < 0.1, < 0.2 etc.) indicate models with minus tolerance for corner-R(re).
| 1 | (mm) | | (mm) | | |
| | (Steel / Edge Length=07) | | (Steel / Edge Length=11) | |
| 4 | | 4 | | |
| 3 | | 3 | | U / USF |
U / USF 2 2 J J / JSF 1 1
F / FSF F / FSF
Каталог Kyocera фрезы MFH для высокоскоростной обработки
Каталог Kyocera фрезы MEC высокопроизводительные концевые и торцевые фрезы
Каталог микроинструмента Kyocera 2015-2016
Каталог Kyocera высокоэффективные сверла со сменными пластинами DRV
Каталог Kyocera пластины TQ для нарезания резьбы c прессованным стружколомом
Каталог Kyocera высокопроизводительные модульные сверла DRA