Основной каталог Kyocera 2016-2017 - страница 85

[Cermet / Coated Carbide / Carbide] How to read pages of “Turning Inserts” B13 （㎜） Description A T φd α ■ 80° Rhombic / Positive with Hole CC_0602_ 6.35 2.38 2.8 7° CC_09T3_ 9.525 3.97 4.4 7° CC_1204_ 12.7 4.76 5.5 7° Free-cutting steel B P rH QP Carbon Steel / Alloy Steel M PP Q Stainless Steel S Gray Cast Iron K Id A Nodular Cast Iron N QP Non-ferrous Metals Insert (Turning) D Q Heat-resistant Alloys T 80 S Q P Titanium Alloys ° H Hard Materials MEGACOAT PVD Chipbreaker Range Dimension MEGACOAT PVD Coated Applicable Toolholders Cermet Coated CVD Coated Carbide DLC Carbide (mm) Cermet Cermet MEGACOAT NANO Carbide Ref. to Page for Applicable Insert Description CA5505 CA5515 CA5525 CA5535 CA6515 CA6525 CA4505 CA4515 PDL025 PR1425 PR1225 PR1305 PR1310 PR1325 PR1535 PR1005 PR1025 PR1125 TN6010 TN6020 PV7010 PV7025 PV7005 PV7020 CA4010 CA4115 CA4120 CA510 CA515 CA525 CA530 PR930 TN610 TN620 PV710 PV720 KW10 SW05 TN60 PV90 Handed Insert rε shows Left-hand 1(: CCET 0602005MFR-J <0.05 NN N 060201MFR-J <0.1 NN N 060201MFL-J <0.1 NN N 060202MFR-J <0.2 NN N 060202MFL-J <0.2 NN N Low Feed 1 CCET 09T301MFR-J <0.1 NN N 09T301MFL-J <0.1 NN N Ref. to the table below B49 09T302MFR-J <0.2 NN N 09T302MFL-J <0.2 NN N 09T304MFR-J <0.4 NN N 09T304MFL-J <0.4 NN N Sharp Edge Non-ferrous Metals CCGT 09T304AH 0.4 NN 09T308AH 0.8 NN Finishing-Medium / Sharp Edge CCGT 09T302R-A3 0.2 NN 09T302L-A3 0.2 NN 09T304R-A3 0.4 NN 09T304L-A3 0.4 NN 2 09T308R-A3 0.8 NN Non-ferrous Metals 09T308L-A3 0.8 NN CCGT 120402R-A3 0.2 NN 120402L-A3 0.2 NN 120404R-A3 0.4 NN E23 120404L-A3 0.4 NN 120408R-A3 0.8 NN 120408L-A3 0.8 NN Finishing-Medium / Sharp Edge Ref. to the table below B49 CCGW 060201 0.1 N 060202 0.2 N Cast Iron CCGW 09T300 0.0 N - 09T301 0.1 N 09T302 0.2 N 09T304 0.4 N Without Chipbreaker · Insert whose corner-R(rε) dimension expressed with less than sign (e.g. < 0.05, < 0.1, < 0.2 etc.) indicate models with minus tolerance for corner-R(rε). 1 2 Applicable Chipbreaker Range (mm) (mm) (Steel) (Non-ferrous Metals) 4 4 ap indicates radius 3 J(09) 3 ap (mm) ap (mm) AH 2 2 J(06) A3 1 1 0.1 0.2 0.3 0.4 0.1 0.2 0.3 0.4 f (mm/rev) f (mm/rev) Inserts are sold in 10 piece boxes ●：Std. Item B55 B - complete.indb 55 06.09.2016 10:01:33