Общий каталог Kemmler 2020 - страница 665

2020 13.69 13 pour des profondeurs de forage sous 8xD. 4. Les données ci-dessus en coupe sont conçus 0,02 mm. tueux. La concentricité doit être inférieure à 3. Ne composez jamais un porte-outil défec- l‘émulsion. ci-dessus sont basées sur l‘utilisation de 2. Les recommandations de données de coupe augmentent en conséquence. stable traitement des données de coupe mandée ou 85% de l‘alimentation. Avec tionner 90% de la vitesse de coupe recom- 1. La première fois que vous utilisez sélec- under 8D. 4. These conditions above are for cutting depth radial run-out of drill must be under 0.02mm. 3. Use a collet without any defect or dust. The with emulsion. 2. The cutting conditions above are for drilling cutting speed and feed rate. conditions remain stable, gradually increase the 85% feed rate mentioned above. If the cutting make a test cutting with 90% of cutting speed or 1. When the tool is used for the first time, please Bohrungstiefen unter 8xD ausgelegt. 4. Die obigen Schnittdaten sind für liegen. Die Rundlaufgenauigkeit muss unter 0,02mm 3. Keine defekte Werkzeugaufnahme wählen. basieren auf dem Einsatz von Emulsion. 2. Die obigen Schnittdatenempfehlungen Schnittdaten entsprechend erhöhen. schubes wählen. Bei stabiler Bearbeitung die Schnittgeschwindigkeit oder 85% des Vor- 1. Beim ersten Einsatz 90% der empfohlenen Données de coupe 8xD Cutting data 8xD Schnittdaten 8xD P H M K N Materialgruppen Wenig legierter Stahl Stahl 30-38HRC Stahl 38-48 HRC Edelstahl GGusseisen Graphit Aluminium Hitzeresistenter Stahl Material groups Low-alloyed steel Steel 30-38HRC Steel 38-48 HRC Stainless Steel Cast Iron Graphite Aluminium Heat resistant steel Groupes matières Acier faible allié Acier 30-38HRC Acier 38-48 HRC Acier inoxydable Fonte Graphite Aluminium Acier thermorésistant Vc 60~120m/min 60~120m/min 40~70m/min 25~40m/min 60~120m/min 50~100m/min 60~140m/min 15~25m/min "Ø „n "f "n "f "n "f "n "f "n "f "n "f "n "f "n "f (mm)" (min-1)“ (mm/r)" (min-1)" (mm/r)" (min-1)" (mm/r)" (min-1)" (mm/r)" (min-1)" (mm/r)" (min-1)" (mm/r)" (min-1)" (mm/r)" (min-1)" (mm/r)" 3 12700 "0.06~0.10" 12700 "0.06~0.10" 7400 "0.06~0.10" 5300 "0.03~0.07" 12700 "0.06~0.10" 9500 "0.06~0.10" 15000 "0.09~0.12" 2100 "0.03~0.06" 4 9600 "0.08~0.12" 9600 "0.08~0.12" 5600 "0.08~0.12" 4000 "0.04~0.08" 9600 "0.08~0.12" 7000 "0.08~0.12" 11100 "0.10~0.15" 1600 "0.04~0.07" 5 7600 "0.10~0.14" 7600 "0.10~0.14" 4500 "0.10~0.14" 3200 "0.05~0.10" 7600 "0.10~0.14" 5700 "0.10~0.14" 9000 "0.10~0.14" 1250 "0.05~0.09" 6 6400 "0.11~0.16" 6400 "0.11~0.16" 3700 "0.11~0.16" 2700 "0.06~0.12" 6400 "0.11~0.16" 4700 "0.11~0.16" 7400 "0.11~0.16" 1050 "0.06~0.11" 8 4800 "0.13~0.19" 4800 "0.13~0.19" 2800 "0.13~0.19" 2000 "0.08~0.16" 4800 "0.13~0.19" 3600 "0.13~0.19" 5600 "0.13~0.19" 800 "0.08~0.14" 10 3800 "0.14~0.22" 3800 "0.14~0.22" 2200 "0.14~0.22" 1600 "0.10~0.18" 3800 "0.14~0.22" 2800 "0.14~0.22" 4500 "0.14~0.22" 600 "0.10~0.16" 12 3200 "0.16~0.24" 3200 "0.16~0.24" 1900 "0.16~0.24" 1300 "0.12~0.20" 3200 "0.16~0.24" 2400 "0.16~0.24" 3700 "0.16~0.24" 500 "0.12~0.18" 14 2700 "0.18~0.28" 2700 "0.18~0.28" 1600 "0.18~0.28" 1100 "0.13~0.22" 2700 "0.18~0.28" 2100 "0.18~0.28" 3200 "0.18~0.28" 450 "0.13~0.20" 16 2400 "0.20~0.29" 2400 "0.20~0.29" 1400 "0.20~0.29" 1000 "0.14~0.25" 2400 "0.20~0.29" 1800 "0.20~0.29" 2800 "0.20~0.29" 400 "0.14~0.23" 18 2100 "0.24~0.32" 2100 "0.24~0.32" 1200 "0.24~0.32" 880 "0.15~0.28" 2100 "0.24~0.32" 1600 "0.24~0.32" 2500 "0.24~0.32" 350 "0.15~0.25"