Общий каталог Kemmler 2017 - 2018 - страница 587

P H M K N Materialgruppen Wenig legierter Stahl Stahl 30-38HRC Stahl 38-48 HRC Edelstahl GGusseisen Graphit Aluminium Hitzeresistenter Stahl Material groups Low-alloyed steel Steel 30-38HRC Steel 38-48 HRC Stainless Steel Cast Iron Graphite Aluminium Heat resistant steel Groupes matières Acier faible allié Acier 30-38HRC Acier 38-48 HRC Acier inoxydable Fonte Graphite Aluminium Acier thermorésistant Vc 60~120m/min 60~120m/min 40~70m/min 25~40m/min 60~120m/min 50~100m/min 60~140m/min 15~25m/min Cutting data 3xD Schnittdaten 3xD "Ø „n "f "n "f "n "f "n "f "n "f "n "f "n "f "n "f (mm)" (min-1)“ (mm/r)" (min-1)" (mm/r)" (min-1)" (mm/r)" (min-1)" (mm/r)" (min-1)" (mm/r)" (min-1)" (mm/r)" (min-1)" (mm/r)" (min-1)" (mm/r)" Données de coupe 3xD 3 12700 "0.09~ "0.09~ "0.09~ "0.03~ "0.09~ "0.09~ "0.09~ "0.03~ 12700 7400 6300 12700 9500 15000 2100 0.12" 0.12" 0.12" 0.07" 0.12" 0.12" 0.12" 0.06" 4 9600 "0.10~ "0.10~ "0.10~ "0.04~ "0.10~ "0.10~ "0.10~ "0.04~ 9600 5600 4700 9600 7000 11100 1600 0.15" 0.15" 0.15" 0.08" 0.15" 0.15" 0.15" 0.07" 5 7600 "0.12~ "0.12~ "0.12~ "0.05~ "0.12~ "0.12~ "0.12~ "0.05~ 7600 4500 3800 7600 5700 9000 1250 0.18" 0.18" 0.18" 0.10" 0.18" 0.18" 0.18" 0.09" 6 6400 "0.14~ "0.14~ "0.14~ "0.06~ "0.14~ "0.14~ "0.14~ "0.06~ 6400 3700 3200 6400 4700 7400 1050 0.20" 0.20" 0.20" 0.12" 0.20" 0.20" 0.20" 0.11" 8 4800 "0.16~ "0.16~ "0.16~ "0.08~ "0.16~ "0.16~ "0.16~ "0.08~ 4800 2800 2400 4800 3600 5600 800 0.24" 0.24" 0.24" 0.16" 0.24" 0.24" 0.24" 0.14" 10 3800 "0.18~ "0.18~ "0.18~ "0.10~ "0.18~ "0.18~ "0.18~ "0.10~ 3800 2200 1900 3800 2800 4500 600 0.27" 0.27" 0.27" 0.18" 0.27" 0.27" 0.27" 0.16" 12 3200 "0.20~ "0.20~ "0.20~ "0.12~ "0.20~ "0.20~ "0.20~ "0.12~ 3200 1900 1600 3200 2400 3700 500 0.30" 0.30" 0.30" 0.20" 0.30" 0.30" 0.30" 0.18" 14 2700 "0.22~ "0.22~ "0.22~ "0.13~ "0.22~ "0.22~ "0.22~ "0.13~ 2700 1600 1350 2700 2100 3200 450 0.35" 0.35" 0.35" 0.22" 0.35" 0.35" 0.35" 0.20" 16 2400 "0.25~ "0.25~ "0.25~ "0.14~ "0.25~ "0.25~ "0.25~ "0.14~ 2400 1400 1200 2400 1800 2800 400 0.36" 0.36" 0.36" 0.25" 0.36" 0.36" 0.36" 0.23" 18 2100 "0.28~ "0.28~ "0.28~ "0.15~ "0.28~ "0.28~ "0.28~ "0.15~ 2100 1200 1050 2100 1600 2500 350 0.38" 0.38" 0.38" 0.28" 0.38" 0.38" 0.38" 0.25" 20 1900 "0.30~ "0.30~ "0.30~ "0.16~ "0.30~ "0.30~ "0.30~ "0.16~ 1900 1100 950 1900 1400 2300 320 0.40" 0.40" 0.40" 0.30" 0.40" 0.40" 0.40" 0.28" 0.02mm. 0,02 mm. l‘émulsion. défectueux. and feed rate. with emulsion. 0,02mm liegen. depth under 5xD. augmentent en conséquence. 4. Die obigen Schnittdaten sind für 3. Ne composez jamais un porte-outil La concentricité doit être inférieure à Die Rundlaufgenauigkeit muss unter Bohrungstiefen unter 5xD ausgelegt. ner 90% de la vitesse de coupe recom- 4. These conditions above are for cutting above. If the cutting conditions remain please make a test cutting with 90% of 3. Use a collet without any defect or dust. mandée ou 85% de l‘alimentation. Avec 1. When the tool is used for the first time, 2. Die obigen Schnittdatenempfehlungen stable traitement des données de coupe ci-dessus sont basées sur l‘utilisation de The radial run-out of drill must be under basieren auf dem Einsatz von Emulsion. die Schnittdaten entsprechend erhöhen. pour des profondeurs de forage sous 5xD. schubes wählen. Bei stabiler Bearbeitung cutting speed or 85% feed rate mentioned Schnittgeschwindigkeit oder 85% des Vor- KEMMLER 1. Beim ersten Einsatz 90% der empfohlenen 2. Les recommandations de données de coupe 1. La première fois que vous utilisez sélection- 4. Les données ci-dessus en coupe sont conçus stable, gradually increase the cutting speed 3. Keine defekte Werkzeugaufnahme wählen. 2. The cutting conditions above are for drilling 12 12.53