Общий каталог Kemmler 2017 - 2018 - страница 579

Schnittdaten 3xD Cutting data 3xD Données de coupe 3xD 1. Beim ersten Einsatz 90% der empfoh- lenen Schnittgeschwindigkeit oder "f 85% des Vorschubes wählen. (mm/r)" "0.02~ 0.04" "0.03~ 0.06" "0.04~ 0.07" "0.05~ 0.09" "0.06~ 0.11" "0.08~ 0.14" "0.10~ 0.16" "0.12~ 0.18" "0.13~ 0.20" "0.14~ 0.23" "0.15~ 0.25" "0.16~ 0.28" Bei stabiler Bearbeitung die Schnitt- daten entsprechend erhöhen. 2. Die obigen Schnittdatenempfeh- 15~25m/min lungen basieren auf dem Einsatz von "n Hitzeresistenter Stahl Heat resistant steel Acier thermorésistant 3200 2100 1600 1250 1050 800 600 500 450 400 350 320 (min-1)" Emulsion. 3. Keine defekte Werkzeugaufnahme wählen. Die Rundlaufgenauigkeit muss unter 0,02mm liegen. "f 4. Die obigen Schnittdaten sind für (mm/r)" "0.06~ 0.08" "0.09~ 0.12" "0.10~ 0.15" "0.12~ 0.18" "0.14~ 0.20" "0.16~ 0.24" "0.18~ 0.27" "0.20~ 0.30" "0.22~ 0.35" "0.25~ 0.36" "0.28~ 0.38" "0.30~ 0.40" Bohrungstiefen unter 5xD ausgelegt. N 1. When the tool is used for the first Aluminium Aluminium Aluminium 60~140m/min time, please make a test cutting with "n 4000 3200 2700 2300 2000 1800 1600 (min-1)" 16000 10600 8000 6400 5300 90% of cutting speed or 85% feed rate mentioned above. If the cutting conditions remain stable, gradually increase the cutting speed and feed "f rate. (mm/r)" "0.06~ 0.08" "0.09~ 0.12" "0.10~ 0.15" "0.12~ 0.18" "0.14~ 0.20" "0.16~ 0.24" "0.18~ 0.27" "0.20~ 0.30" "0.22~ 0.35" "0.25~ 0.36" "0.28~ 0.38" "0.30~ 0.40" 2. The cutting conditions above are for drilling with emulsion. Graphit Graphite Graphite 3. Use a collet without any defect or dust. 50~100m/min The radial run-out of drill must be "n 7400 5600 4500 3700 2800 2200 1900 1600 1400 1200 1100 under 0.02mm. (min-1)" 11000 4. These conditions above are for cutting depth under 5xD. "f 1. La première fois que vous utilisez (mm/r)" "0.06~ 0.08" "0.09~ 0.12" "0.10~ 0.15" "0.12~ 0.18" "0.14~ 0.20" "0.16~ 0.24" "0.18~ 0.27" "0.20~ 0.30" "0.22~ 0.35" "0.25~ 0.36" "0.28~ 0.38" "0.30~ 0.40" sélectionner 90% de la vitesse de coupe recommandée ou 85% de Fonte l‘alimentation. Avec stable traitement GGusseisen Cast Iron 60~120m/min des données de coupe augmentent en "n 9500 7000 5700 4700 3600 2800 2400 2100 1800 1600 1400 conséquence. (min-1)" 14000 2. Les recommandations de données de coupe ci-dessus sont basées sur l‘utilisation de l‘émulsion. "f 3. Ne composez jamais un porte-outil (mm/r)" "0.02~ 0.05" "0.03~ 0.07" "0.04~ 0.08" "0.05~ 0.10" "0.06~ 0.12" "0.08~ 0.16" "0.10~ 0.18" "0.12~ 0.20" "0.13~ 0.22" "0.14~ 0.25" "0.15~ 0.28" "0.16~ 0.30" défectueux. La concentricité doit être inférieure à 0,02 mm. Edelstahl 4. Les données ci-dessus en coupe sont 25~40m/min Stainless Steel Acier inoxydable conçus pour des profondeurs de forage "n 5500 3700 2700 2200 1850 1400 1100 930 800 700 620 550 sous 5xD. (min-1)" "f 0.24" (mm/r)" "0.06~ 0.08" "0.09~ 0.12" "0.10~ 0.15" "0.12~ 0.18" "0.14~ 0.20" "0.16~ "0.18~ 0.27" "0.20~ 0.30" "0.22~ 0.35" "0.25~ 0.36" "0.28~ 0.38" "0.30~ 0.40" 40~70m/min Stahl 38-48 HRC Steel 38-48 HRC Acier 38-48 HRC "n 9500 6300 4700 3800 3100 2400 1900 1600 1400 1200 1100 950 (min-1)" "f (mm/r)" "0.06~ 0.08" "0.09~ 0.12" "0.10~ 0.15" "0.12~ 0.18" "0.14~ 0.20" "0.16~ 0.24" "0.18~ 0.27" "0.20~ 0.30" "0.22~ 0.35" "0.25~ 0.36" "0.28~ 0.38" "0.30~ 0.40" Stahl 30-38HRC Steel 30-38HRC Acier 30-38HRC 60~120m/min "n 9500 7000 5700 4700 3600 2800 2400 2100 1800 1600 1400 (min-1)" 14000 "f (mm/r)" "0.06~ 0.08" "0.09~ 0.12" "0.10~ 0.15" "0.12~ 0.18" "0.14~ 0.20" "0.16~ 0.24" "0.18~ 0.27" "0.20~ 0.30" "0.22~ 0.35" "0.25~ 0.36" "0.28~ 0.38" "0.30~ 0.40" P H M K 12 12 Acier faible allié 60~120m/min Wenig legierter Stahl Low-alloyed steel „n 7000 5700 4700 3600 2800 2400 2100 1800 1600 1400 (min-1)“ 14000 9500 Vc "Ø 2 3 4 5 6 8 10 12 14 16 18 20 (mm)" Materialgruppen Material groups Groupes matières KEMMLER 12.45