Каталог Iscar токарный инструмент 2017 - страница 544
Навигация
Каталог Iscar резьбонарезные фрезы
Каталог Iscar инструмент для обработки алюминиевых колёс
Каталог Iscar державки и пластины для нарезания резьбы 2022
Каталог Iscar расточные системы 2022
Каталог Iscar высокоточные развертки и метчики 2022
Токарные инструменты Iscar (часть 2) 2026
Thread Helix Angle and Anvil Selection
Pitch TPI mm 2.5 10
Use AE Anvils for EX-RH
Special Holder Required ACME STUB ACME
9 and IN-LH Toolholders.
trapez (din 103)
| 3 | 8 | AE or Al+4.5º Use Al Anvils for IN-RH |
| round (din 405) | ||
| and EX-LH Toolholders. | ||
| 3.5 | 7 | AE or Al+3.5º |
| 4 | 6 | AE or Al+2.5º |
| 5 | 5 | λ° |
| Standard Anvil (supplied with toolholder) | ||
| 6 | 4 | |
| 3.5 | α° | |
| 8 | 3 | 1.5° |
| 10 | 2.5 | |
| 12 | 2 | AE or Al+0.5º |
| 16 | 1.5 | Toolholder |
5 10 20 30 40 50 60 70 80 mm
Diameter
Pitch TPI mm 2.5 10
Special Holder Required Partial Profiles 60º Partial
9 Profiles 55º ISO, UN,
| 3 | 8 | WHIT., NPT, BSPT AE or Al+4.5º Use AE Anvils for EX-RH |
| 3.5 | 7 | AE or Al+3.5º and IN-LH Toolholders. |
| Use Al Anvils for IN-RH | ||
| 4 | 6 | AE or Al+2.5º |
| and EX-LH Toolholders. | ||
| 5 | 5 | |
| 6 | 4 | |
| 3.5 | Standard Anvil (supplied with toolholder) | |
| 8 | 3 | |
| 10 | 2.5 | |
| 12 | 2 | |
| 16 | 1.5 |
| 5 | 10 | 20 | 30 | 40 | 50 | 60 | 70 | 80 | mm | ||
| Diameter | |||||||||||
| Pitch | |||||||||||
| TPI | mm |
2.5 10 Use AE Anvils for EX-RH
| Special Holder Required | American Buttress | and IN-LH Toolholders. | |
| 9 | |||
| Sagengewinde | Use Al Anvils for IN-RH |
| 3 | 8 | (DIN-513) AE or Al+2.5º | |
| and EX-LH Toolholders. | |||
| 3.5 | 7 | ||
| 4 | 6 | Standard Anvil (supplied with toolholder) | |
| Replacing the | |||
| 5 | 5 | =3.74 | |
| α° standard anvil | |||
| 6 | 4 | with a negative | |
| 3.5 | Change to Negative Anvil AE or Al-1.5º | angle anvil | |
| 8 | 3 | ||
| γ=1.5° | will eliminate | ||
| 10 | 2.5 | ||
| 12 | 2 | side rubbing | |
| 16 | 1.5 | Toolholder |
5 10 20 30 40 50 60 70 80 mm
Diameter