Каталог Iscar державки и пластины для нарезания резьбы 2022 - страница 17

THREADING
PNA RE
PDPT
GIQR/L-MT WF
Internal Threading Inserts with a L
60° Partial Profile for Threading
in 8 mm and Larger Holes
Left-hand shown
NUT
60° Dimensions

SCREW


IC528
Designation L RE PNA PDPT(1) WF DMIN(2) TPN(3) TPX(4) TPIN(5) TPIX(6)
GIQR/L 8-MT-0.05 7.78 0.05 60.0 1.50 4.80 8.00 0.500 1.590 16.00 50.00 •
GIQR/L 11-MT-0.05 10.68 0.05 60.0 2.00 6.70 11.00 0.500 2.300 11.00 50.00 •
• Can be used for thread milling by circular interpolation • Pitch max 0.19xD • D-diameter of thread • For cutting speed recommendations, see page 711
(1) Cutting depth maximum
(2) Minimum diameter
(3) Thread pitch minimum (mm)
(4) Thread pitch maximum (mm)
(5) Threads per inch minimum
(6) Threads per inch maximum
For tools, see pages: MG (414) • MGCH (414)


OAL
X
DCONMS PDX
PICCO R/L-60°-Thread PDX 60°
Inserts with a 60° Internal a WF HC
Thread Profile for 2.4 mm x
CF
Min. Bore Diameter OHN
Right-hand shown
NUT
60° Dimensions Tough 1 Hard

SCREW


IC228

IC908
Designation DCONMS HC CF PDX WF a OHN(1) OAL DMIN TPN(2) TPX(3) TPIN(4) TPIX(5)
PICCO R 003.0105-8 4.00 0.27 0.04 0.3 0.30 2.30 8.0 22.00 2.40 0.500 0.700 36.00 48.00 •
PICCO R 004.0105-10 4.00 0.27 0.09 0.4 1.00 3.00 10.0 24.00 3.20 0.500 0.750 36.00 48.00 •
PICCO R/L 004.0205-15 4.00 0.27 0.06 0.4 1.50 3.50 15.0 30.00 4.00 0.500 0.750 36.00 48.00 •
PICCO R/L 005.0205-15 5.00 0.27 0.06 0.4 1.90 4.40 15.0 30.00 5.00 0.500 0.750 36.00 48.00 •
PICCO L 005.0407-15 5.00 0.40 0.09 0.5 1.90 4.40 15.0 30.00 5.00 0.750 1.000 24.00 36.00 •
PICCO R 005.0407-15 5.00 0.40 0.09 0.5 1.90 4.40 15.0 30.00 5.00 0.750 1.000 24.00 36.00 • •
PICCO R 005.0407-20 5.00 0.40 0.09 0.5 1.90 4.40 20.0 35.00 5.00 0.750 1.000 24.00 36.00 •
PICCO R/L 005.0510-15 5.00 0.55 0.12 0.6 1.90 4.40 15.0 30.00 4.80 1.000 1.250 20.00 24.00 •
PICCO R 005.0510-20 5.00 0.55 0.12 0.6 1.90 4.40 20.0 35.00 4.80 1.000 1.250 20.00 24.00 •
PICCO R/L 006.0510-15 6.00 0.55 0.12 0.6 2.30 5.30 15.0 30.00 6.00 1.000 1.250 20.00 24.00 •
PICCO R 006.0510-22 6.00 0.55 0.12 0.6 2.30 5.30 22.0 37.00 6.00 1.000 1.250 20.00 24.00 •
PICCO R/L 006.0612-15 6.00 0.68 0.15 0.7 2.30 5.30 15.0 30.00 6.00 1.250 1.500 16.00 20.00 •
PICCO R 006.0612-22 6.00 0.68 0.15 0.7 2.30 5.30 22.0 37.00 6.00 1.250 1.500 16.00 20.00 •
PICCO R/L 006.0815-15 6.00 0.81 0.18 0.8 2.30 5.30 15.0 30.00 6.00 1.500 1.750 14.00 16.00 •
PICCO R 006.0815-22 6.00 0.81 0.18 0.8 2.30 5.30 22.0 37.00 6.00 1.500 1.750 14.00 16.00 •
PICCO R/L 007.0815-15 7.00 0.81 0.18 0.8 2.70 6.30 15.0 30.00 7.00 1.500 1.750 14.00 16.00 •
• For detailed cutting data, see page 711
(1) Minimum overhang
(2) Thread pitch minimum (mm)
(3) Thread pitch maximum (mm)
(4) Threads per inch minimum
(5) Threads per inch maximum
For holders, see pages: GHPCOR (361) • PICCO ACE (359) • PICCO/MG PCO (holder) (360)


651