Каталог Widia all star 2020 - страница 273

• TABLE OF CONTENTS
• INDEXABLE MILLING
• 0º/90º SHOULDER MILLS
• 90° HIGH-SPEED CUTTING MILLS
• FACE MILLS
• HIGH-FEED MILLS
• COPY MILLS
• SOLID END MILLING
• HIGH-PERFORMANCE SOLID CARBIDE END MILLS
• GENERAL PURPOSE SOLID CARBIDE END MILLS
• HOLEMAKING
• SOLID CARBIDE DRILLS
• MODULAR DRILLS
• INDEXABLE DRILLS
• TAPPING
• TURNING
• HIGH-PERFORMANCE INSERTS
• GROOVING & CUT-OFF
• Informational Icons Guide
• Material Overview • DIN

TURNINGTAPPINGHOLEMAKINGSOLID END MILLINGINDEXABLE MILLING Indexable Drills • Top Cut 4™ TC4 • Insert Selection Guide Stable Cutting Conditions Unstable Cutting Conditions Interrupted Cutting Conditions Material Geometry periphery periphery periphery Group insert centre insert insert centre insert insert centre insert P1 V38 WU25CH WU40PH WU40PH WU40PH WU40PH WU40PH P2–P4 V34 WPK10CH WU40PH WU25CH WU40PH WU40PH WU40PH P5–P6 V36 WU25CH WU40PH WU40PH WU40PH WU40PH WU40PH M1–M3 V36 WU25CH WU40PH WU40PH WU40PH WU40PH WU40PH K1–K3 V34 WPK10CH WU40PH WU40PH WU40PH WU40PH WU40PH N1–N4 V36 WN10PH WN10PH WN10PH WN10PH WN10PH WN10PH S1–S4 V38 WU40PH WU40PH WU40PH WU40PH WU40PH WU40PH NOTE: All speed conditions are for stable conditions. For unstable conditions, it is suggested to reduce starting speeds by 10%. For interrupted cuts, reduce by 20%. For 4 x D, it is highly recommended to start with feed and speed values reduced by 10% less than above data. For 5 x D, diameter range 12–23,99mm (insert sizes A to C), it is highly recommended to start with feed and speed values reduced by 20% less than above data. For 5 x D, diameter range 25–68mm (inserts sizes D to H), it is highly recommended to start with feed and speed values reduced by 15% less than above data. For 4 x D and 5 x D, it is recommended to reduce feed rate during entry and exit by 30–50%. TC4 • Cutting Data • Metric Recommended Feed Rate per Revolution MaterialGroupGeometry GradecentreperipheryCutting Speed — vcm/minminStartmaxToolDiameter 12,00–13,99 14,00–18,99 Insert 19,00–23,99 Insert 24,00–29,99 InsertInsert Size ASize BSize CSize D P0 –V38 WU40PH WU25CH 120 180 260 mm/rev 0,06–0,08 0,08–0,11 0,10–0,13 0,11–0,14 P1 –V38 WU40PH WU25CH 120 180 260 mm/rev 0,06–0,10 0,08–0,13 0,10–0,15 0,11–0,16 P2 –V34 WU40PH WU25CH 120 190 280 mm/rev 0,06–0,10 0,08–0,15 0,10–0,16 0,11–0,17 P3 –V34 WU40PH WPK10CH 120 200 310 mm/rev 0,08–0,15 0,10–0,16 0,11–0,18 0,12–0,20 P4 –V34 WU40PH WPK10CH 120 190 310 mm/rev 0,08–0,15 0,10–0,16 0,11–0,18 0,12–0,20 P5 –V36 WU40PH WU25CH 120 180 250 mm/rev 0,06–0,10 0,08–0,14 0,10–0,15 0,11–0,16 P6 -V36 WU40PH WU25CH 120 160 210 mm/rev 0,06–0,10 0,08–0,14 0,10–0,15 0,11–0,16 M1 -V38 WU40PH WU40PH 120 160 240 mm/rev 0,06–0,11 0,07–0,11 0,08–0,12 0,10–0,14 M2 –V38 WU40PH WU40PH 110 140 210 mm/rev 0,06–0,10 0,07–0,11 0,08–0,12 0,10–0,14 M3 -V36 WU40PH WU40PH 100 120 200 mm/rev 0,06–0,10 0,07–0,11 0,08–0,12 0,10–0,14 K1 -V34 WU25CH WPK10CH 120 200 280 mm/rev 0,08–0,14 0,08–0,16 0,10–0,18 0,12–0,24 K2 –V34 WU40PH WPK10CH 100 180 260 mm/rev 0,08–0,14 0,08–0,16 0,10–0,18 0,12–0,24 K3 -V34 WU40PH WPK10CH 100 170 240 mm/rev 0,08–0,14 0,08–0,16 0,10–0,18 0,12–0,24 N1 -V36 WN10PH WN10PH 250 350 500 mm/rev 0,06–0,10 0,08–0,14 0,10–0,15 0,11–0,16 N2 –V36 WN10PH WN10PH 150 300 450 mm/rev 0,06–0,10 0,08–0,14 0,10–0,15 0,11–0,16 N3 -V36 WN10PH WN10PH 80 120 150 mm/rev 0,06–0,10 0,07–0,11 0,08–0,12 0,10–0,14 S3 -V38 WU40PH WU40PH 20 30 45 mm/rev 0,08–0,12 0,08–0,13 0,10–0,15 0,12–0,19 S4 –V38 WU40PH WU40PH 35 40 65 mm/rev 0,08–0,12 0,08–0,13 0,10 –0,15 0,12–0,19 MaterialGroupGeometry GradecentreperipheryCutting Speed — vcm/minminStartmaxToolDiameter 30,00–36,99 37,00–45,99 46,00–56,99 57,00–68,00Insert Size EInsert Size FInsert Size GInsert Size H P0 –V38 WU40PH WU25CH 120 180 260 mm/rev 0,13–0,16 0,15–0,18 0,16–0,23 0,17–0,24 P1 –V38 WU40PH WU25CH 120 180 260 mm/rev 0,13–0,17 0,15–0,19 0,16–0,24 0,17–0,25 P2 –V34 WU40PH WU25CH 120 190 280 mm/rev 0,13–0,20 0,15–0,21 0,16–0,28 0,17–0,30 P3 –V34 WU40PH WPK10CH 120 200 310 mm/rev 0,16–0,24 0,16–0,24 0,18–0,30 0,19–0,32 P4 –V34 WU40PH WPK10CH 120 190 310 mm/rev 0,14–0,22 0,16–0,24 0,18–0,30 0,19–0,32 P5 –V36 WU40PH WU25CH 120 180 250 mm/rev 0,13–0,18 0,15–0,20 0,16–0,28 0,17–0,30 P6 -V36 WU40PH WU25CH 120 160 210 mm/rev 0,13–0,18 0,15–0,20 0,16–0,28 0,17–0,29 M1 -V38 WU40PH WU40PH 120 160 240 mm/rev 0,12–0,17 0,14–0,21 0,16–0,23 0,16–0,24 M2 –V38 WU40PH WU40PH 110 140 210 mm/rev 0,12–0,17 0,14–0,21 0,16–0,23 0,16–0,24 M3 -V36 WU40PH WU40PH 100 120 200 mm/rev 0,12–0,17 0,14–0,21 0,16–0,23 0,16–0,24 K1 -V34 WU25CH WPK10CH 120 200 280 mm/rev 0,14–0,26 0,16–0,30 0,18–0,32 0,20–0,36 K2 –V34 WU40PH WPK10CH 100 180 260 mm/rev 0,14–0,26 0,16–0,30 0,18–0,32 0,20–0,36 K3 -V34 WU40PH WPK10CH 100 170 240 mm/rev 0,14–0,26 0,16–0,30 0,18–0,32 0,20–0,36 N1 -V36 WN10PH WN10PH 250 350 500 mm/rev 0,13–0,18 0,15–0,20 0,16–0,28 0,17–0,30 N2 –V36 WN10PH WN10PH 150 300 450 mm/rev 0,13–0,18 0,15–0,20 0,16–0,28 0,17–0,30 N3 -V36 WN10PH WN10PH 80 120 150 mm/rev 0,12–0,17 0,14–0,21 0,16–0,23 0,16–0,24 S3 -V38 WU40PH WU40PH 20 30 45 mm/rev 0,14–0,21 0,16–0,24 0,18–0,26 0,20–0,30 S4 –V38 WU40PH WU40PH 35 40 65 mm/rev 0,14–0,21 0,16–0,24 0,18–0,26 0,20–0,30 NOTE: All speed conditions are for stable conditions. For unstable conditions, it is suggested to reduce starting speeds by 10%. For interrupted cuts, reduce by 20%. For 4 x D, it is highly recommended to start with feed and speed values reduced by 10% less than above data. For 5 x D, diameter range 12–23,99mm (insert sizes A to C), it is highly recommended to start with feed and speed values reduced by 20% less than above data. For 5 x D, diameter range 25–68mm (inserts sizes D to H), it is highly recommended to start with feed and speed values reduced by 15% less than above data. For 4 x D and 5 x D, it is recommended to reduce feed rate during entry and exit by 30–50%. widia.com C73