Общий каталог Sumitomo 2019 - 2020 - страница 275

HolderHolder MaterialMaterial WF WF WF Ref. PageRef. Page Legend Very Smal Diameter TurningBars Smal Diameter TurningBoring SEC-Boring Bar S-SVJB / B-SVJB Type Steel93° Internal ProfilingScrew-on S-SVJB Fig 1 DMIN Min.Bore Dia. Fig 2 DMIN Min.Bore Dia. Concave Facing and Bottom Facing DCON52° 52° DCON 93° 93° -5° LH3 HLHDLF GAMF LH3LHD HLF -5° -5° Figure shows right-hand (R) tool. E Holder Parts Dimensions (mm) Cat. No. Stock Min.BoreDia.DiameterHeightOverallLengthCuttingEdgeDistanceHeadHeadRakeAngleApplicable Insert Fig Flat Screw Wrench C R L Cat. No. Nm DMIN DCON H LF WF LHD LH3 GAMF (For Torx Holes) S20R-SVJB R/L1103-25 ●● 25SteelS25S-SVJB R/L1103-30S32T-SVJB R/L1604-40●●●●3040S40T-SVJB R/L1604-50●●502025192002.04229242503.55036QQVB□□1103 B120 11 BFTX02508NV 1.5 TRX083240303003.575373004.5956075-8°-7°VB□□1604B12122BFTX035082.0TRX10D Right-handed (R) tool holders are compatible with left-handed (L) or neutral (N) inserts. Left-handed (L) tool holders are compatible with right-handed (R) or neutral (N) inserts. R Steel with Internal Profiling Anti-Vibration93°Mechanism Screw-on B-SVJB Fig 1 DMIN Min.Bore Dia. S DCON Concave Facing and Bottom Facing 52° 93° -5° LH3LHD HLF T -5° Figure shows right-hand (R) tool. V Holder Parts Dimensions (mm) Cat. No. Stock Min.BoreDia.Diameter Height OverallLengthCuttingEdgeDistanceHeadHeadApplicable Insert Fig Flat Screw Wrench W R L Cat. No. Nm DMIN DCON H LF WF LHD LH3 (For Torx Holes) Steel with B20R-SVJB R/L1103-25 ●● 25Anti-VibrationMechanismB25S-SVJB R/L1103-30●●302025192002.0242503.5556237.545VB□□1103 B120 11 BFTX02508NV 1.5 TRX08 Right-handed (R) tool holders are compatible with left-handed (L) or neutral (N) inserts. Left-handed (L) tool holders are compatible with right-handed (R) or neutral (N) inserts. Applicable Inserts S-SVJB / B-SVJB / S-SVQB / B-SVQB / C-SVQB / S-SVUB / B-SVUB / C-SVUB / S-SVZB / B-SVZB / C-SVZB Type 1st Recommended Insert ● Refer as well to the Insert Selection Guide (page A10 on).● Some combinations need to be made to order or cannot be manufactured. Name ofChipbreaker/GUCBN/PCDPhotoGradeAC8025P Cutting Range P (Steel) M (Stainless Steel) K (Cast Iron) S (Exotic Alloy) N (Non-ferrous) H (Hardened Steel) Process Finishing Medium Cutting Finishing Medium Cutting High-speed Finishing Finishing to Medium Cutting Finishing to Medium Cutting Finishing to Medium Cutting Coated Uncoated General FB SU LB SU SUMIBORON No Chipbreaker SI AY SUMIBORON SUMIBORON Cutting T1500Z AC8025P AC6030M AC8025P BN7000/BNC500 AC4015K AC5015S H1 BNC2020 BN2000 High FYS SI FYS SI SUMIBORONPrecisionAC1030UAC1030UAC1030UAC1030U BN7000/BNC500—SIAC5015S— SUMIBORON SUMIBORONBNC2010BN1000 RecommendedCutting Conditions A10 on A14 on A16 on A18 on A22 on A20 on BNC500 is for ductile cast iron. N m Recommended Tightening Torque (N·m) E31