Общий каталог Sumitomo 2018 - 2019 - страница 364

4 4 Flutes Endmills GSX MILL Endmills GSX 40000C-4D Type Resistant Alloy Pre-hardened Ti Alloy / Heat Structual Steel Alloy Steel Carbon Steel Coated Hardened Steel Stainless GSX Graphite Die Steel Tempered Cast iron Cu Alloy Al Alloy Carbide Steel Steel 45~55 55~60 60~65 Endmills HRC HRC HRC Grades Coating  ◎ ◎ ◎ ◎ ◎  ◎   (mm) Cat. No. Stock øD 1 2 L ød ød h5 øD GSX 40100C-4D l 1,0 4,0 5,0 40 4 GSX 40150C-4D l 1,5 6,0 7,0 40 4 GSX 40200C-4D 1 l 2,0 8,0 9,0 40 4 GSX 40250C-4D 2 L l 2,5 10,0 11,0 50 4 GSX 40300C-4D l 3,0 12,0 13,5 50 6 30° ( øD) (mm) GSX 40400C-4D l 4,0 16,0 17,5 50 6 40 GSX40000C-4D GSX 40500C-4D l 5,0 20,0 22,0 60 6 Helix Angle Corner : C Type 30 1.5D 2D 3D 4D GSX 40600C-4D l 6,0 24,0 – 60 6 øDc Tolerance 20 GSX 40800C-4D l 8,0 32,0 – 80 8 D ≤ 3,0 0 – 0,015 10 GSX 41000C-4D l 10,0 40,0 – 90 10 3,0 < D ≤ 12 0 – 0,020 12,0 < D 0 – 0,030 0 20 40 60 80 100 ( 1 ) GSX 41200C-4D l 12,0 48,0 – 100 12 GSX 41600C-4D l 16,0 64,0 – 120 16 Grade: ACF20 GSX 42000C-4D 20,0 80,0 – 140 20  n Endmill Identification (GSX MILL Series) GSX 4 0100 C - 4D j k l m n Series No. of Diameter Cutting Cutting Edge Code Teeth Edge Length ( S:C: Sharp Gash Land Drilling ) Edge n Recommended Cutting Conditions Endmills Coated 1. For stable machining performance use rigid, high-precision machines and holders. 2. Use air blowing when dry machining. 3. Use wet machining for stainless steel, heat resistant alloy, and titanium alloy applications. 4. In rear cases, chattering may occur in early milling stages, dissipating after 2m of cutting. doc 5. If chattering is a problem, reduce the spindle speed and feed rate indicated in the table below by the same ratio, or reduce the depth of cut. 6. This series is not recommended for grooving. woc 7. If the machine cannot achieve the recommended spindle speed, please use the max. spindle speed available. l Shoulder Milling Work Material Tempered Steel, Heat Resistive Carbon Steel Hardened Steel Alloy Steel Structural Steel Cast Iron Hardened Steel Stainless Steel Steel, Cond. (150 to 250HB) (45 to 55HRC) (25 to 35HRC) (35 to 45HRC) Titanium Alloy Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate Spindle Speed Feed Rate øD (mm) (rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min) (rpm) (mm/min) 1,0 9.000 140 9.000 140 9.000 140 7.000 80 6.500 60 4.500 40 5.400 40 4.500 40 2,0 4.500 140 4.500 140 4.500 140 3.500 100 3.200 80 2.300 55 2.700 55 2.300 40 4,0 2.250 200 2.250 200 2.250 200 1.750 120 1.600 100 1.200 60 1.350 50 1.200 35 6,0 1.500 250 1.500 250 1.500 250 1.150 160 1.050 140 800 65 900 45 800 35 8,0 1.100 220 1.100 220 1.100 220 850 160 800 130 600 65 660 45 600 35 10,0 900 210 900 210 900 210 700 140 650 120 460 65 540 45 460 35 12,0 750 200 750 200 750 200 580 140 520 110 400 65 450 45 400 35 16,0 550 170 550 170 550 170 440 120 400 95 300 55 330 45 300 35 20,0 450 150 450 150 450 150 350 100 320 80 240 50 270 45 240 35 Shoulder doc 3,5 D 3,0 D cutting woc øD< 3: 0,04 D , 3 ≤ øD< 8: 0,08 D , 8 ≤ øD: 0,1 D 0,02 D J19