Общий каталог SGS 2021 - страница 30

FRACTIONAL Z-Carb-HPR 37° POS 5 TOLERANCES (inch) ≠ 1/8–1/4 DIAMETER DC = +0.0000/–0.0012 DCON = h6 RE = +0.0000/–0.0020 >1/4–3/8 DIAMETER LF DC = +0.0000/–0.0016 APMX DCON = h6 Z5 •Z5CR RE = +0.0000/–0.0020DCDCON>3/8–1 DIAMETERDC= +0.0000/–0.0020NCDDCON = h6 FRACTIONAL SERIES RE RE = +0.0000/–0.0020 CONTINUED inch EDP NO. NON- • An ideal balance of helix,indexing, flute depth, CUTTING TI-NAMITE-A TI-NAMITE-MCUTTINGLENGTHOVERALLSHANKCORNERCENTERTI-NAMITE-ATI-NAMITE-A(TA)TI-NAMITE-MTI-NAMITE-M(TM)DIAMETEROF CUTLENGTHDIAMETERRADIUSDIAMETER(TA)(TA)W/INTERNAL(TM)(TM)W/INTERNAL rake and relief DC APMX LF DCON RE NCD W/FLAT COOLANT W/ FLAT COOLANT • Variable indexing forchatter supression and1/25/8 3 1/2 – 0.1750 38506 38512 37320 37024 37030 37321 patented edge geometry 1/2 5/8 3 1/2 0.010 0.1750 38827 38829 38831 38826 38828 38830 for shearing and strength• Chatter-free geometry1/25/83 1/2 0.015 0.1750 38533 38578 37330 37025 37031 37331 allows deep cutting and 1/2 5/8 3 1/2 0.030 0.1750 38534 38579 37332 37026 37032 37333 high speed machining• Central coolant hole1/25/8 3 1/2 0.060 0.1750 38535 38580 37334 37027 37033 37335 delivers coolant 1/2 5/8 3 1/2 0.090 0.1750 38536 38581 37337 37028 37034 37338 effectively to the cuttingzone enhancing chip1/25/8 3 1/2 0.120 0.1750 38537 38582 37339 37029 37035 37340 removal when pocketingor slotting1/2 1 3 1/2 – 0.1750 38507 38513 37322 37036 37042 37323 • Excels at roughing, 1/2 1 3 1/2 0.010 0.1750 38833 38835 38837 38832 38834 38836 ramping, high speedmachining and finishing1/21 3 1/2 0.015 0.1750 38538 38583 37341 37037 37043 37342 in a variety of materials 1/2 1 3 1/2 0.030 0.1750 38539 38584 37343 37038 37044 37344 • Enhanced cornergeometry with tight1/2 1 3 1/2 0.060 0.1750 38540 38585 37345 37039 37045 37346 tolerance corner radii 1/2 1 3 1/2 0.090 0.1750 38541 38586 37348 37040 37046 37349 • Recommended formaterials ≤ 45 HRc1/2 1 3 1/2 0.120 0.1750 38542 38587 37350 37041 37047 37351 (≤ 420 Bhn) 1/2 1-1/4 3-1/4 1/2 – 0.1750 37190 37194 37325 37048 37054 37324 1/2 1-1/4 3-1/4 1/2 0.010 0.1750 38839 38841 38843 38838 38840 38842 1/2 1-1/4 3-1/4 1/2 0.015 0.1750 37191 37195 37352 37049 37055 37353 STEELS 1/2 1-1/4 3-1/4 1/2 0.030 0.1750 37192 37196 37354 37050 37056 37355 STAINLESS STEELS 1/2 1-1/4 3-1/4 1/2 0.060 0.1750 37193 37197 37356 37051 37057 37357 CAST IRON 1/2 1-1/4 3-1/4 1/2 0.090 0.1750 38543 38588 37359 37052 37058 37360 HIGH TEMP ALLOYS 1/2 1-1/4 3-1/4 1/2 0.120 0.1750 38544 38589 37361 37053 37059 37362 TITANIUM 5/8 3/4 3-1/2 5/8 – 0.2630 38508 38514 38518 37060 37067 37260 HARDENED STEELS 5/8 3/4 3-1/2 5/8 0.010 0.2190 38845 38847 38849 38844 38846 38848 5/8 3/4 3-1/2 5/8 0.015 0.2190 38545 38590 38623 37061 37068 37261 For patent 5/8 3/4 3-1/2 5/8 0.030 0.2190 38546 38591 38624 37062 37069 37262 information visit 5/8 3/4 3-1/2 5/8 0.060 0.2190 38547 38592 38625 37063 37070 37263 www.ksptpatents.com 5/8 3/4 3-1/2 5/8 0.090 0.2190 38548 38593 38626 37064 37071 37264 5/8 3/4 3-1/2 5/8 0.120 0.2190 38549 38594 38627 37065 37072 37265 5/8 3/4 3-1/2 5/8 0.190 0.2190 38550 38595 38628 37066 37073 37266 5/8 1-1/4 3-1/2 5/8 – 0.2190 37198 37202 38519 37074 37081 37267 continued on next page 30 END MILLS wwwE.kNyDoMceILraLS-sgstool.com