HSK-T TOOLS TypeGeneral 60°General 55° Class UP20M NX2525 UTi20TNumber of Passes HTi10 PNAPNA W1ICW1IC HSK-T TOOLS FOR MULTI-TASK MACHINES INSERTS FOR MT TYPE Coated Cermet Carbide Dimensions (mm) ISO Order Number Pitch mm(thread / inch)IC W1 RE Geometry MTTR436000 G s s ─ 0.8 12.7 4.76 0 MTTR/L(60°) (G Class) MTTR436001 G s s s s 1.0 ─ 1.75 12.7 4.76 0.1 MTTL436001 G s s s 1.0 ─ 1.75 12.7 4.76 0.1 RE MTTR436002 G s s s s 2.0 ─ 2.5 12.7 4.76 0.2 MTTL436002 G s s 2.0 ─ 2.5 12.7 4.76 0.2 MTTR436003 G s s s s 3.0 ─ 3.5 12.7 4.76 0.3 MTTL436003 G s s 3.0 ─ 3.5 12.7 4.76 0.3 MTTR436004 G s s 4.0 ─ 4.5 12.7 4.76 0.4 Right hand insert shown. MTTR435501 G s s (28 ─ 10) 12.7 4.76 0.1 MTTR(55°) (G Class) MTTR435502 G s s (16 ─ 8) 12.7 4.76 0.2 MTTR435503 G s s (11 ─ 8) 12.7 4.76 0.3 RE Right hand insert shown. y STANDARD OF DEPTH OF CUT aMetric Screw Thread Unit : mm P (Pitch) 0.75 1.00 1.25 1.50 1.75 2.00 2.50 3.00 3.50 4.00 4.50 h1 0.46 0.61 0.77 0.92 1.07 1.23 1.53 1.84 2.15 2.45 2.76 H a The chart on the right shows the cutting h2 0.35 0.47 0.59 0.70 0.82 0.94 1.17 1.41 1.65 1.87 2.11 depths when machining external ISO r (Corner Radius) 0.11 0.14 0.18 0.22 0.25 0.29 0.36 0.43 0.50 0.58 0.65 metric screw threads. 1 0.18 0.20 0.20 0.25 0.25 0.25 0.30 0.30 0.35 0.35 0.40 a When using cermet grades or cutting 2 0.13 0.15 0.18 0.20 0.20 0.25 0.25 0.25 0.30 0.30 0.35 stainless steel, please increase thenumber of passes by 2 or 3 extrapasses. 3 0.10 0.10 0.12 0.15 0.20 0.20 0.20 0.25 0.25 0.25 0.3040.050.100.120.150.150.150.200.200.200.250.2550.060.100.100.120.150.150.200.200.250.25 6 0.05 0.07 0.10 0.10 0.10 0.15 0.20 0.20 0.20 7 0.05 0.08 0.10 0.15 0.15 0.20 0.20 8 0.05 0.10 0.10 0.15 0.15 0.15 9 0.08 0.10 0.10 0.15 0.15 10 0.05 0.09 0.10 0.10 0.15 11 0.05 0.10 0.10 0.10 12 0.05 0.10 0.10 13 0.05 0.10 14 0.06 Note 1) The first pass causes a high load on the cutting edge. In order to avoid damage, keep the depth of cut to 0.4 ─ 0.5 mm maximum. s : Stocked in Japan H018 <10 inserts in one case>