Каталог Iscar концевые фрезы со сменными пластинами 2022 - страница 31

ENDMILLS • SOLID CARBIDE • MULTI-MASTER T490 ELN-11 90° Endmills Carrying DC DCONMS T490 LN#T 11... Tangentially Clamped Inserts APMX LU LH OAL Designation DC CICT(4) LH LU APMX OAL DCONMS Shank(5) RMPX°(6) kg T490 ELN D22-2-W25-11 (1) 22.00 2 35.0 33.0 9.00 95.00 25.00 W - 0.29 SR 34-535-SN/L9.3 BLD T15/S7(a) SW6-SD T490 ELN D25-3-C24-11B (2) 25.00 3 35.0 33.0 9.00 200.00 24.00 C 1.7 0.64 SR 34-535/L9.5-SN BLD T15/S7(a) SW6-SD T490 ELN D25-3-C25-11 (3) 25.00 3 35.0 33.0 9.00 120.00 25.00 C 1.7 0.40 SR 34-535/L9.5-SN BLD T15/S7(a) SW6-SD T490 ELN D25-3-W25-11 (3) 25.00 3 35.0 33.0 9.00 95.00 25.00 W 1.7 0.30 SR 34-535/L9.5-SN BLD T15/S7(a) SW6-SD T490 ELN D32-3-C32-11 32.00 3 40.0 38.0 9.00 130.00 32.00 C 1.5 0.73 SR 34-535-SN BLD T15/S7(a) SW6-SD T490 ELN D32-3-C32-11B (2) 32.00 3 40.0 38.0 9.00 200.00 32.00 C 1.5 1.16 SR 34-535-SN BLD T15/S7(a) SW6-SD T490 ELN D32-3-W32-11 32.00 3 40.0 38.0 9.00 110.00 32.00 W 1.5 0.60 SR 34-535-SN BLD T15/S7(a) SW6-SD T490 ELN D32-4-C32-11 32.00 4 40.0 38.0 9.00 130.00 32.00 C 1.5 0.73 SR 34-535-SN BLD T15/S7(a) SW6-SD T490 ELN D32-4-W32-11 32.00 4 40.0 38.0 9.00 110.00 32.00 W 1.5 0.60 SR 34-535-SN BLD T15/S7(a) SW6-SD T490 ELN D40-4-C32-11 40.00 4 44.0 38.0 9.00 130.00 32.00 C 1.4 0.84 SR 34-535-SN BLD T15/S7(a) SW6-SD T490 ELN D40-4-W32-11 40.00 4 44.0 38.0 9.00 115.00 32.00 W 1.4 0.75 SR 34-535-SN BLD T15/S7(a) SW6-SD T490 ELN D40-5-C32-11 40.00 5 44.0 38.0 9.00 130.00 32.00 C 1.4 0.83 SR 34-535-SN BLD T15/S7(a) SW6-SD • Important: Maximum clamping torque 3.2 N*m (1) Recommended cutting conditions: at ap=6 mm, fz=0.12 mm/t at ap=8 mm, fz=0.10 mm/t (2) Long cylindrical shank (3) Recommended cutting conditions: at ap=6 mm, fz=0.15 mm/t at ap=8 mm, fz=0.12 mm/t (4) Number of inserts (5) C-Cylindrical, W-Weldon (6) Maximum ramping angle - valid only with T490 LNHT 1106PNTR-RD insert (a) Recommended key handle for limiting torque to 3.2 N*m for this item is HSD 4-3.2NM (to be used with BLD 4 T15-4.8 blade) For inserts, see pages: T490 LNMT/LNHT 1106 (477) OAL T890HT ELN-R13 90° Endmills Carrying T890 LN.T 1306... DC DCONMS Tangentially Clamped Inserts with 8 Cutting Edges APMX LU LH Designation DC APMX CICT(1) DCONMS Shank(2) LU LH OAL kg T890HT ELN D32-3-C32-13 32.00 9.50 3 32.00 C 37.40 40.0 130.00 0.68 T890HT ELN D32-3-C32-13B 32.00 9.50 3 32.00 C 47.40 50.0 250.00 1.43 T890HT ELN D32-3-W32-13 32.00 9.50 3 32.00 W 37.40 40.0 110.00 0.56 T890HT ELN D40-4-C32-13 40.00 9.50 4 32.00 C - 44.0 130.00 0.12 T890HT ELN D40-4-W32-13 40.00 9.50 4 32.00 W - 40.0 115.00 0.69 (1) Number of inserts (2) C-Cylindrical, W-Weldon For inserts, see pages: T890 LN.. 1306 (475) Spare Parts Designation T890HT ELN-R13 SR 10513105(a) BLD IP20/M7 SW6-T-SH (a) Recommended tightening torque: 8.0 N*m (71.0 lbf*in) 29