Общий каталог Ingersoll 2011 - страница 907

• 0003 Table of Contents
• 0006 End Mills
• 0064 Long Edge
• 0104 0Deg Face Mills
• 0160 Face Mills
• 0202 Slotters
• 0218 Form Mills
• 0236 Profile Mills
• 0302 Milling Tech
• 0384 Solid Carbide
• 0448 Solid Carbide Tech
• 0474 Holemaking & Thread Milling
• 0666 Holemaking & Thread Milling Tech
• 0720 Innofit Top On Toolholders
• 0738 HSK Toolholders
• 0774 CAT Toolholders
• 0796 BT Toolholders
• 0816 Adaptions Accessories
• 0872 Turning Inserts
• 1024 Turning Holders
• 1144 Turning Tech
• 1174 Threading Inserts
• 1242 Threading Holders
• 1256 Threading Tech
• 1268 T-Clamp
• 1344 T-Clamp Tech
• 1376 T-CAP
• 1388 T-CAP Tech
• 1394 Product_Index

GradeGrade K10K10 TT5030TT1300 TT9030TT7310 DNGG ML CHIPBREAKER NEGATIVE 55 DEGREE RHOMBIC GROUND INSERT FOR MEDIUM LIGHT MACHINING/VERY SHARP 55° d R l t ANSI ISO feed ap l d t R Number Number (ipr) (inch) DNGG431ML DNGG150404ML .007 (.004-.012) .047 (.031-.138) 0.594 0.500 0.187 0.016 DNGG432ML DNGG150408ML .010 (.005-.014) .059 (.039-.138) 0.579 0.500 0.187 0.031 For use in holders MDJNR/L, MDQNR/L, TDJNR/L, TDNNN, TDQNR/L, A-TDUNR/L,see pages 1050, 1051, 1090, 1091, 1091, 1138.=P=M =K =N =S =H DNMA NEGATIVE 55 DEGREE RHOMBIC FLAT TOP INSERT FOR ROUGHING 55° d R l t ANSI ISO feed ap l d t R Number Number (ipr) (inch) *DNMA332 DNMA110408 .014 (.006-.020) .059 (.031-.118) 0.425 0.375 0.187 0.031 *DNMA333 DNMA110412 .017 (.006-.020) .059 (.031-.118) 0.413 0.375 0.187 0.047 DNMA431 DNMA150404 .012 (.006-.020) .079 (.016-.157) 0.594 0.500 0.187 0.016 DNMA432 DNMA150408 .017 (.006-.026) .079 (.031-.157) 0.579 0.500 0.187 0.031 DNMA433 DNMA150412 .020 (.006-.026) .079 (.047-.157) 0.567 0.500 0.187 0.047 DNMA441 DNMA150604 .012 (.006-.020) .079 (.016-.157) 0.594 0.500 0.250 0.016 DNMA442 DNMA150608 .017 (.006-.026) .079 (.031-.157) 0.579 0.500 0.250 0.031 DNMA443 DNMA150612 .020 (.006-.026) .079 (.047-.157) 0.567 0.500 0.250 0.047 *Insert is screw heldFor use in holders MDJNR/L, MDQNR/L, SDJNR/L, TDJNR/L, TDNNN, TDQNR/L, A-SDQNR/L, A-SDUNR/L, A-TDUNR/L,=P=M =K =N =S =H see pages 1050, 1051, 1069, 1090, 1091, 1129, 1138. 909